Focus Fanatics Forum banner

1 - 20 of 28 Posts

·
Registered
Joined
·
150 Posts
Discussion Starter · #1 ·
Has anyone done an install on a zx4 st??? [poke]

Do you still need to cut it?

I have the kit ready to install im just wondering how long it should take...

thanks

mason
 

·
Boost Addict
Joined
·
2,628 Posts
http://www.focushacks.com/index.php?modid=33


The only link you will need to install your new exhaust. Its simple really. Maybe 1-2 hours to do.
Also, you might not need to do everything in the instructions (Ex. - cutting bolts if they have rusted on the old exhaust).
 

·
Gal. 2:20
Joined
·
1,999 Posts
ya, exhaust/CAI/SRI all easy mods...it's when you start doing the internals then you get a bit more complicated....
 

·
Registered
Joined
·
7,530 Posts
Well I have an ST and yes I had to cut it out. Someone has done it before without cutting it in half but I tried and wasn't able to.
 

·
BodyKits=PantiesDrop
Joined
·
13,168 Posts
sometimes the ST's don't require cutting due to their lack of lunchbox...i enjoy the sawzall personally however
 

·
Freeskiing Fanatic!
Joined
·
5,455 Posts
yea, I had to cut the pipe on my friends to get it on there.
 

·
BEWST AGAIN YAY!!!!!
Joined
·
6,851 Posts
Yeah I just did mine this past Monday...05 ST and had to cu it so it can come over the rear axle...but if you have two people you may not have too
 

·
Freeskiing Fanatic!
Joined
·
5,455 Posts
^nah dude, i had three people, and it was still undo-able, even with that many.
 

·
has a screw loose
Joined
·
9,927 Posts
So , you all recommend 2 people to do this ? The exhaust I ordered from MBRP is suppose to be a direct bolt on or at least I'm hoping so. And it should be here next week sometime as they had to manufacture it after I ordered it .
 

·
love my red focus
Joined
·
1,793 Posts
yes, i had someone help me with my mbrp exhaust on my ses w/sap
 

·
BEWST AGAIN YAY!!!!!
Joined
·
6,851 Posts

·
has a screw loose
Joined
·
9,927 Posts
Lightning2nd , I have the 07 ZX 4 Se with the SAP . Did your exhaust bolt right up without any problems?
 

·
BEWST AGAIN YAY!!!!!
Joined
·
6,851 Posts
when you get it it should be in 3 pieces, and you should have no problems with the SAP as long as you let MBRP know when you ordered it...I will have to say that I am happy with the exhaust I got from them...direct bolt on
 

·
has a screw loose
Joined
·
9,927 Posts
Gonefhsn, Sounds good ; about how long did it take you to hook it up ?
 

·
BEWST AGAIN YAY!!!!!
Joined
·
6,851 Posts
about 2.5 Hours...but I was doing it by myself...Cjohn364 came over (cuz I didn't call him till then) right after I the stock system out of the car...and Thanks I love the way it sounds and the throttle response is [headbang]
 

·
has a screw loose
Joined
·
9,927 Posts
when you get it it should be in 3 pieces, and you should have no problems with the SAP as long as you let MBRP know when you ordered it...I will have to say that I am happy with the exhaust I got from them...direct bolt on
I told them it was for the 2.0l Sedan but I never mentioned anything to them about it having a SAP on it .

But when I went to the web site it sends you to a certain model for the 2.3. So when I called them I told them I needed 1 for the Sedan version and he set me up with a direct replaced .
 

·
BEWST AGAIN YAY!!!!!
Joined
·
6,851 Posts
I dont know if there is a diff between there exhaust for SAP and non SAP like there is with some manufacutres..I would call them back and ask. Has it shipped yet?
 

·
has a screw loose
Joined
·
9,927 Posts
Shipping out this morning , I'm gonna call now and see if it's gonna make a difference and hopefully find out .

Ok , I just got off the phone with them and it hasn't shipped out yet so they told me they would check and make sure it would fit with SAP and do any adjustments before it leaves .

Whewwww that was close
 
1 - 20 of 28 Posts
Top