Focus Fanatics Forum banner

1 - 9 of 9 Posts

·
Registered
Joined
·
194 Posts
Discussion Starter · #1 · (Edited)
I have few aftermarket parts up for grabs.
Seller: Me
I Will only accept Paypal and prices include shipping and Paypal fees
Make me some offers the worst I can say is no.

Focus central under drive pulley 2pc $70 shipped
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010988_zpsa157793e.jpg

CFM 65mm throttle body for SVT models $165 shipped
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010990_zps446fc79e.jpg

Steeda intake tube for SVT focus $40 shipped
[NOTE: Tube and connectors only. No hose clamps or filter.
Also Note tube has mark on it.]
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010991_zps98c5b308.jpg
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010992_zps4108eb81.jpg

K&N fipk system for focus SVT $120 shipped

I added some heat reflection tape to the heat shield. Also I trimmed down the shield a bit to make it fit with my strut bar.
It is missing the bracket (K&N part#1 07167) that goes from the tube to the valve cover. I never installed the bracket due to it getting in the way and its pretty much useless. The rubber seal has a tare by the spot where the tube sat and rubbed.
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010994_zpsee3be2ba.jpg
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010995_zps4033b83a.jpg

I have few aftermarket parts up for grabs.
Seller: Me
I Will only accept Paypal and prices include shipping and Paypal fees

Focus central under drive pulley 2pc $70 shipped
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010988_zpsa157793e.jpg

CFM 65mm throttle body for SVT models $165 shipped
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010990_zps446fc79e.jpg

Steeda intake tube for SVT focus $40 shipped
[NOTE: Tube and connectors only. No hose clamps or filter.
Also Note tube has mark on it.]
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010991_zps98c5b308.jpg
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010992_zps4108eb81.jpg

K&N fipk system for focus SVT $120 shipped

I added some heat reflection tape to the heat shield. Also I trimmed down the shield a bit to make it fit with my strut bar.
It is missing the bracket (K&N part#1 07167) that goes from the tube to the valve cover. I never installed the bracket due to it getting in the way and its pretty much useless. The rubber seal has a tare by the spot where the tube sat and rubbed.
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010994_zpsee3be2ba.jpg
http://i805.photobucket.com/albums/yy337/TACO_BELL_ROCKS/P1010995_zps4033b83a.jpg

AEM CAI for the SVT models. $120 shipped

It is painted black. Not perfect. Has some black overspray inside the tubes,
the tubes have some nicks from rubbing, and have slight indents from the hose clamps. But is 100% functional

It's missing the rubber bumper bolt/washers/nuts for the lower radiator mount.

Also missing hose clamps and maf screws. These can be acquired at any reputable hardware store.

You can get the rubber bumper mount from Summit racing for like $2
AEM Induction Air Intake Rubber Mounts 1228599

The filter is in almost new condition. besides that it was used for like 7000 miles


I will also include a AEM pre-filter, the license plate frame, 1 AEM sticker, install instructions. It will be shipped in the original AEM box.



 

·
Registered
Joined
·
194 Posts
Discussion Starter · #4 ·
I goggled it and only found the CFM 67mm throttle body. Did you mean 67mm?
I was told it was a 65mm when I bought it. Maybe it's a prototype, or a earlier model. It worked on my SVT so I know it's for the SVT model.
 

·
Registered
Joined
·
0 Posts
hey loaded still have the udrive pulley set for 70? if so i'll take them I live near montreal but I will have an address in ny or Vermont soon. I'll probably have it tomorrow or toosday. I imagine the shipping shouldn't be too steep.
 
1 - 9 of 9 Posts
Top