Focus Fanatics Forum banner

1 - 7 of 7 Posts

·
Registered
05 ST -2.5L fusion swap 13 ST - SP63 forged block
Joined
·
107 Posts
Discussion Starter #1 (Edited)
Selling a 63mm throttle body
pulled from a 2011 2.5L duratec with 30,000 miles on it.

This may be of interest for anyone with the 2.0L ecoboost/Ti-VCT That wants more throttle response than the stock 57mm throttle body offers.
I believe it will bolt up nicely to any Ti-VCT (if you know more please comment)

There is an interesting thread posted by FF user Shade-010 where they test the effect of the 63mm swap on the dyno. you be the judge:

https://www.focusfanatics.com/forum/duratec-ti-vct-performance-2012-current/810781-63mm-tb-na.html

No tune required, but as mentioned in the thread a tune helps optimize any bolt-on.

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28783-63mm-throttle-body-no-caliper-picture-but-i-have-measured-really-63mm-will-upload-picture-caliper-when-i-get-back-my-apartment.html

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28781-63mm-throttle-body1.html

asking $60 including shipping obo

*I know there is no picture with a caliper. I left my caliper at school, can upload a pic with it when I go back.. I have measured it and it is definitely 63mm ID
 

·
Registered
05 ST -2.5L fusion swap 13 ST - SP63 forged block
Joined
·
107 Posts
Discussion Starter #3
Hmm.. it reallly looks similar to that 2.3L ecoboost throttle body. Same bolt patern and servo placement. I assumed the exact dimensions were the same since the ecoboost TB and the 2.5L TB are both 63mm.

Interested to see if it fits. Thanks for checking!
 

·
Registered
05 ST -2.5L fusion swap 13 ST - SP63 forged block
Joined
·
107 Posts
Discussion Starter #6
I pulled out the caliper and spec'd everything that seemed of interest

the plug looks identical from what I can tell, its just in a slightly different location. there are some close ups. I can't imagine why it wouldn't work. could use some good pics of the 63mm ecoboost TB to really be certain.

there are two dimensions of the bolt pattern on the back. if you put the caliper tongs in the bolt holes, they are about 58mm apart in both directions (bolts are in a square pattern)

here's the new pics:
https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28797-rear-dimension.html

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28795-connector-2.html

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28793-connector-1.html

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28791-dimension3.html

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28787-dimension1.html

https://www.focusfanatics.com/forum/members/habriant40-albums-parts-sale-picture28785-id63.html
 

·
Registered
05 ST -2.5L fusion swap 13 ST - SP63 forged block
Joined
·
107 Posts
Discussion Starter #7
^^ if it does not fit I'll gladly do a return. I don't want to rip anyone off.
 
1 - 7 of 7 Posts
Top