Cooling Fan Motor and Shroud, Accessory Drive Belt, Thermostat Housing - Ford Focus Forum, Ford Focus ST Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Second Generation > DURATEC Performance (2008-2011)

DURATEC Performance (2008-2011) The place to chat about any Duratec 20 engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Reply
 
Thread Tools Display Modes
Old 05-09-2012, 10:38 AM   #1
dcorwin822
Focus Enthusiast
 
dcorwin822's Avatar
 
Join Date: Jan 2008
Fan#: 53054
Location: Binghamton, NY
What I Drive: 2008 Vermillion Red SES

Posts: 173
FF Reputation: 11 dcorwin822 Great Standing Member
Buy-Sell-Trade Rating: (0)
Post Cooling Fan Motor and Shroud, Accessory Drive Belt, Thermostat Housing

Cooling Fan Motor and Shroud




Removal and Installation

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Maintenance/Service and Repair.
2. Remove the lower radiator air deflector.
3. Disconnect the cooling fan motor and shroud electrical connector and the pin-type retainers.
4. Remove the 2 bolts and remove the cooling fan motor and shroud from the vehicle.
To install, tighten to 5 Nm (44 lb-in).
5. To install, reverse the removal procedure.

Accessory Drive Belt



Removal and Installation

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Maintenance/Service and Repair.
2. Remove the 2 bolts and the accessory drive belt splash shield.
To install, tighten to 9 Nm (80 lb-in).
3. Using the hex feature, rotate the accessory drive belt tensioner clockwise and remove the accessory drive belt.
4. To install, reverse the removal procedure.

Thermostat Housing





Removal and Installation

NOTE: The thermostat and thermostat housing are serviced as an assembly. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Maintenance/Service and Repair.
1. Drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding.
2. Remove the accessory drive belt. For additional information, refer to Drive Belts, Mounts, Brackets and Accessories.
3. Remove the 2 nuts and position aside the power steering tube.
To install, tighten to 10 Nm (89 lb-in).
4. Remove the cooling fan motor and shroud. For additional information, refer to Cooling Fan Motor and Shroud.
5. Remove the 2 bolts, the stud bolt and position aside the A/C compressor.
To install, tighten to 25 Nm (18 lb-ft).
6. Disconnect the radiator and heater hoses from the thermostat housing.
7. Remove the 3 bolts, thermostat housing and thermostat as an assembly.
To install, tighten to 10 Nm (89 lb-in).
8. NOTE: Lubricate the thermostat housing O-ring with clean engine coolant. To install, reverse the removal procedure.
9. Fill and bleed the cooling system.


dcorwin822 is offline  
    Reply With Quote
Sponsored Links
Advertisement
 
Old 05-09-2012, 10:40 AM   #2
dcorwin822
Focus Enthusiast
 
dcorwin822's Avatar
 
Join Date: Jan 2008
Fan#: 53054
Location: Binghamton, NY
What I Drive: 2008 Vermillion Red SES

Posts: 173
FF Reputation: 11 dcorwin822 Great Standing Member
Buy-Sell-Trade Rating: (0)
Above is for a 2008 Focus. I'm to assume other years apply.
dcorwin822 is offline  
    Reply With Quote
Old 09-10-2012, 10:52 AM   #3
rwolverine
Focus Rookie
 
Join Date: Sep 2012
Fan#: 103666
Location: Grand Rapids, United States
What I Drive: 05 honda accord EX 5spd

Posts: 1
FF Reputation: 1 rwolverine Good Standing Member
Buy-Sell-Trade Rating: (0)
now to find the pretty pictures for removing the intake manifold so i can get to the thermostat housing!
rwolverine is offline  
    Reply With Quote
Old 09-10-2012, 12:09 PM   #4
VEGAS
Focus Enthusiast
 
VEGAS's Avatar
 
Join Date: Jun 2010
Fan#: 75680
Location: Las Vegas, NV
What I Drive: 2007 Focus

Posts: 537
FF Reputation: 4 VEGAS Good Standing Member
Buy-Sell-Trade Rating: (0)
it should apply to 2.3L and 2.0L Duratec 2003-2011 But is 100% 2005-2010 2.0L
not sure about 2011 but should be same there to in USA models..
VEGAS is offline  
    Reply With Quote
Old 09-10-2012, 12:11 PM   #5
dcorwin822
Focus Enthusiast
 
dcorwin822's Avatar
 
Join Date: Jan 2008
Fan#: 53054
Location: Binghamton, NY
What I Drive: 2008 Vermillion Red SES

Posts: 173
FF Reputation: 11 dcorwin822 Great Standing Member
Buy-Sell-Trade Rating: (0)
Quote:
Originally Posted by rwolverine View Post
now to find the pretty pictures for removing the intake manifold so i can get to the thermostat housing!
You don't need to take it off. You can get to it from below and from above. It's just tight.
dcorwin822 is offline  
    Reply With Quote
Reply

Bookmarks & Social Networks
-->
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:03 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.