sucking air: intake manifold - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Technical Chat

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Reply
 
Thread Tools Display Modes
Old 02-19-2013, 01:40 PM   #1
jscot
Focus Rookie
 
Join Date: Nov 2012
Fan#: 106744
Location: Gibsons, Canada
What I Drive: 2001 Gold SE

Posts: 5
FF Reputation: 1 jscot Good Standing Member
Buy-Sell-Trade Rating: (0)
sucking air: intake manifold

Hey folks, thanks for the great info on here. I've had rough idle when hot issue on my wife's 2001 since I changed the head.

I've diagnosed it to leaking around the intake manifold on the driver's side.

I'm assuming it was uneven torquing on my part rather than bad (new) gaskets. Or maybe I reversed the gaskets? I'll have to double check, but I think I put the fat gasket closest to the head. Anyone know the order of the 2 intake manifold gaskets?

Also, should I try and loosen everything off and re-torque? Some of those buggers are tough to get to!

Thanks for any wisdom!


jscot is offline  
    Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 02-19-2013, 04:24 PM   #2
zetecDon
Where am I?
 
zetecDon's Avatar
 
Join Date: Feb 2009
Fan#: 62506
Location: east of Cincinnati, OH
What I Drive: 02 ZX3, 02 MX-5

Posts: 7,966
Points 12,875, Level 74
Points: 12,875, Level: 74 Points: 12,875, Level: 74 Points: 12,875, Level: 74
Level Up 7% Completed
Level up: 7% Level up: 7% Level up: 7%
Forum Activity 29%
Activity: 29% Activity: 29% Activity: 29%
FF Reputation: 28 zetecDon Great Standing Member
Buy-Sell-Trade Rating: (45)
Moved to "General Technical Chat".
zetecDon is offline  
    Reply With Quote Quick reply to this message
Old 02-20-2013, 02:00 PM   #3
sailor
Elder
 
sailor's Avatar
 
Join Date: Jun 2008
Fan#: 57268
Location: Williamsville, NY
What I Drive: 2004 Pitch Black ZTS 2.3 5spd.

Posts: 16,811
Points 12,042, Level 71
Points: 12,042, Level: 71 Points: 12,042, Level: 71 Points: 12,042, Level: 71
Level Up 98% Completed
Level up: 98% Level up: 98% Level up: 98%
Forum Activity 99%
Activity: 99% Activity: 99% Activity: 99%
FF Reputation: 79 sailor Excellent Standing Member
Buy-Sell-Trade Rating: (0)
Access being a PITA, retorquing after loosening using a center to outside circular pattern (in steps) would be the first thing to try. I think I'd try to get it loose enough that you could squeeze a little black RTV between the surfaces where it leaked to aid in re-sealing it. (otherwise the labor involved in completely removing & replacing would indicate new gaskets & inspection of mating surfaces B4 re-installation)

Hope you get lucky, at least you found the issue & now it's just the pain of managing to repair it!
sailor is online now  
    Reply With Quote Quick reply to this message
Old 02-20-2013, 09:22 PM   #4
amc49
Focus Fanatic
 
Join Date: Mar 2012
Fan#: 96610
Location: Fort Worth, TX
What I Drive: 00 wagon, 02 sedan both zetec atx

Posts: 5,595
Points 3,227, Level 35
Points: 3,227, Level: 35 Points: 3,227, Level: 35 Points: 3,227, Level: 35
Level Up 18% Completed
Level up: 18% Level up: 18% Level up: 18%
Forum Activity 59%
Activity: 59% Activity: 59% Activity: 59%
FF Reputation: 25 amc49 Great Standing Member
Buy-Sell-Trade Rating: (0)
As long as part has not been installed long enough to cook the gasket into the compressed shape you should be able to remove it and let part sit to expand gasket back out, of course that means car cannot be used for a while. I have helped that by dunking gasket in acetone to swell it, and let gasket again sit for 3-4 days for acetone (VOC) to de-gas out of the rubber and then reuse part. The acetone swell/shrink thing helps the part to remember its' original form. As far as bolt torque, the bolts hit solid and then no more gasket compression can occur anyway, simply feeling bolt carefully hit solid means it is torqued. You CANNOT squeeze this type gasket more for sealing. all you are doing is breaking the part, like so many do to the stat housings here onsite.
amc49 is online now  
    Reply With Quote Quick reply to this message
Reply

Bookmarks & Social Networks

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:42 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat