"How To" - Clutch Master Cylinder Replacement - Ford Focus Forum, Ford Focus ST Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Closed Thread
 
Thread Tools Display Modes
Old 10-26-2005, 07:50 PM   #1
pokeySVT
Focus Jr. Enthusiast
 
Join Date: Aug 2005
Fan#: 26986
Location: Bountiful, UT
What I Drive: 2002 Pitch Black SVT

Posts: 40
FF Reputation: 1 pokeySVT Good Standing Member
Buy-Sell-Trade Rating: (0)
"How To" - Clutch Master Cylinder Replacement

Well I just finished this repair on my 02 SVTF. While it was not fun, it was not nearly as difficult as some people lead me to believe. I thought that it might be good to have a list of tips and tricks that I used for others in case anyone wants to attempt this repair.

(1). I started by removing my airbox and intake tube (I left the MAFS alone)
(2). Then I unclipped the fuse box from the fire wall and pulled it towards the front of the car to let me access the clutch hydralic lines.
(3). Move to the inside of the vehicle and remove the clutch pedal position sensor and the clutch interlock sensor.
(4). Unbolt the master cylinder from the pedal assembly bracket, a metric sized GearWrench will greatly speed up this process.
(5). Once the master cylinder was unbolted from the pedal assembly bracket I loosen the entire pedal assembly bracket, there are four nuts that need to be loosened and a looong extension will allow access to the top two.
(6). With the bracket loosened I moved back to the engine compartment and unbolted the junction block (where the lines pass through the fire walll), then I removed the clips that hold the hydralic lines in place.
(Tip!!) Here is a little trick to help stop fluid loss from the resevior, I pulled the rubber cap off of the clutch bleeder screw and put it on the line that runs from the resevior to the master cylinder.
(7). I found that it was easier to push the master cylinder back into the car as I removed the lower clutch line.
(Tip!!) Here is the second tip that I learned, make sure that you put the lower line back into the master cylinder before you bolt the master cylinder to anything.
(8). Reinstall in reverse order and have a friend help bleed the system.

All in all it took me about 1.5 hours to complete the repair, and I think that it is well within an average mechanics abilities, no special tools required.!!


__________________
Help me!!

Last edited by pokeySVT; 10-26-2005 at 11:40 PM.
pokeySVT is offline  
    Quick reply to this message
Sponsored Links
Advertisement
 
Old 10-27-2005, 12:25 AM   #2
Portuga
Focus Enthusiast
 
Portuga's Avatar
 
Join Date: Apr 2005
Fan#: 22452
Location: Newark NJ
What I Drive: 2002 Blue Focus SVT

Posts: 459
FF Reputation: 1 Portuga Good Standing Member
Buy-Sell-Trade Rating: (5)
Did you get the newer updated part, the one that doesn't break down for no reason?
If so, what is the part number so I can order it?
__________________
SVT Squad #84
RP Engine\Trans Syntetic _ Fidanza Flywheel _ Clutchmasters FX100 _ VF Rear Engine Mount _ Hyp SRI _ Hyp 93 Oct Tune _ Grounding Kit _ Taylor 8.2mm Wires _ Autolite Double Platinums _ Clutch Sensor Mod
Portuga is offline  
    Quick reply to this message
Old 10-27-2005, 02:09 PM   #3
pokeySVT
Focus Jr. Enthusiast
 
Join Date: Aug 2005
Fan#: 26986
Location: Bountiful, UT
What I Drive: 2002 Pitch Black SVT

Posts: 40
FF Reputation: 1 pokeySVT Good Standing Member
Buy-Sell-Trade Rating: (0)
I was not aware that there was an updated part #, I just got mine from the local Ford store. I will look-up the part number that I got and let you know
__________________
Help me!!
pokeySVT is offline  
    Quick reply to this message
Old 10-28-2005, 01:03 AM   #4
WD40
The Librarian
 
WD40's Avatar
 
Join Date: Mar 2004
Fan#: 5157
Location: Helena, MT
What I Drive: '04 Sonic Blue - SVT 3Door

Posts: 13,116
FF Reputation: 138 WD40 Excellent Standing Member WD40 Excellent Standing Member
Buy-Sell-Trade Rating: (3)
It's a "sticky".
WD40 is offline  
    Quick reply to this message
Old 11-05-2005, 05:07 PM   #5
pokeySVT
Focus Jr. Enthusiast
 
Join Date: Aug 2005
Fan#: 26986
Location: Bountiful, UT
What I Drive: 2002 Pitch Black SVT

Posts: 40
FF Reputation: 1 pokeySVT Good Standing Member
Buy-Sell-Trade Rating: (0)
Quote:
Originally posted by Portuga
Did you get the newer updated part, the one that doesn't break down for no reason?
If so, what is the part number so I can order it?
Sorry about the delay, here is the part number that I used. 1M5Z-7A543-AA

hope that helps
__________________
Help me!!
pokeySVT is offline  
    Quick reply to this message
Old 11-08-2005, 01:20 PM   #6
skicat
Focus Rookie
 
Join Date: Jan 2005
Fan#: 17600
Location: Pontiac, MI
Posts: 16
FF Reputation: 1 skicat Good Standing Member
Buy-Sell-Trade Rating: (0)
more tips?

This is a great post and much appreciated. Just a few of questions:

What is a GearWrench?

Did you bleed the system from the master? slave? both?

Where is the slave cylinder located?

Thanx for yr help.
skicat is offline  
    Quick reply to this message
Old 09-06-2006, 09:50 AM   #7
elwood125
Focus Enthusiast
 
elwood125's Avatar
 
Join Date: Jan 2005
Fan#: 17784
Location: 757massive, VA
What I Drive: Mk 3 Blue Candy SE Sport 5spd Hatch

Posts: 460
Points 1,079, Level 17
Points: 1,079, Level: 17 Points: 1,079, Level: 17 Points: 1,079, Level: 17
Level Up 79% Completed
Level up: 79% Level up: 79% Level up: 79%
Forum Activity 3%
Activity: 3% Activity: 3% Activity: 3%
FF Reputation: 4 elwood125 Good Standing Member
Buy-Sell-Trade Rating: (1)
the part # for an 00-01 is the ys4z-7a543-aa



is the 1m5z an improved part??


is clutch pedal travel a problem you have when this fails??
elwood125 is offline  
    Quick reply to this message
Old 09-06-2006, 10:35 AM   #8
b16sir1991
Focused Focus
 
b16sir1991's Avatar
 
Join Date: Dec 2004
Fan#: 16612
Location: Kannapolis, NC
What I Drive: 2004 SVT Focus, Sonic Blue

Posts: 6,403
Points 12,236, Level 72
Points: 12,236, Level: 72 Points: 12,236, Level: 72 Points: 12,236, Level: 72
Level Up 47% Completed
Level up: 47% Level up: 47% Level up: 47%
Forum Activity 0%
Activity: 0% Activity: 0% Activity: 0%
FF Reputation: 175 b16sir1991 Excellent Standing Member b16sir1991 Excellent Standing Member
Buy-Sell-Trade Rating: (116)
That YS4Z# is for an early 2000-'01 model. 1M5Z-9A543-AB is the later one.
__________________
"The right driver can work magic"

Oct 2005 Ride of the month.
SVT Squad #25
Call me Mike......

Give rep points and feedback when you appreciate someone on here!
b16sir1991 is offline  
    Quick reply to this message
Old 09-06-2006, 10:36 AM   #9
b16sir1991
Focused Focus
 
b16sir1991's Avatar
 
Join Date: Dec 2004
Fan#: 16612
Location: Kannapolis, NC
What I Drive: 2004 SVT Focus, Sonic Blue

Posts: 6,403
Points 12,236, Level 72
Points: 12,236, Level: 72 Points: 12,236, Level: 72 Points: 12,236, Level: 72
Level Up 47% Completed
Level up: 47% Level up: 47% Level up: 47%
Forum Activity 0%
Activity: 0% Activity: 0% Activity: 0%
FF Reputation: 175 b16sir1991 Excellent Standing Member b16sir1991 Excellent Standing Member
Buy-Sell-Trade Rating: (116)
Your part# superceeds to a 98AB-9A543-AH for the early ones.
__________________
"The right driver can work magic"

Oct 2005 Ride of the month.
SVT Squad #25
Call me Mike......

Give rep points and feedback when you appreciate someone on here!
b16sir1991 is offline  
    Quick reply to this message
Old 09-11-2006, 08:46 AM   #10
elwood125
Focus Enthusiast
 
elwood125's Avatar
 
Join Date: Jan 2005
Fan#: 17784
Location: 757massive, VA
What I Drive: Mk 3 Blue Candy SE Sport 5spd Hatch

Posts: 460
Points 1,079, Level 17
Points: 1,079, Level: 17 Points: 1,079, Level: 17 Points: 1,079, Level: 17
Level Up 79% Completed
Level up: 79% Level up: 79% Level up: 79%
Forum Activity 3%
Activity: 3% Activity: 3% Activity: 3%
FF Reputation: 4 elwood125 Good Standing Member
Buy-Sell-Trade Rating: (1)
so they are not interchangeable? I am still having clutch pedal travel issues and after replacing the clutch and slave cylinder, flywheel am getting a little panicky. any help advice would be nice.


elwood125@hotmail.com
elwood125 is offline  
    Quick reply to this message
Closed Thread

Bookmarks & Social Networks

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:06 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.