Timing pin and bar measurements? - Focus Fanatics
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace



Go Back   Focus Fanatics > Ford Focus Tech Discussions > General Technical Chat

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
FocusFest Ford Focus Tire & Wheels FocusFanatics Merchandise

Reply
 
Thread Tools Display Modes
Old 03-19-2013, 11:20 PM   #1
Deus Machina
Focus Jr. Enthusiast
 
Join Date: Jun 2012
Fan#: 100167
Location: Brandon, FL
What I Drive: 2000 black ZX3

Posts: 38
FF Reputation: 1 Deus Machina Good Standing Member
Buy-Sell-Trade Rating: (0)
Timing pin and bar measurements?

Sorry for the separate thread, but it wouldn't be seen in the other one. My timing belt snapped, I'll need the tools.

Anyone have ones they can measure? Thread size, length, and diameter of the pin, and dimensions of the bar?

I'll have a touch time scraping together money for the timing kit, let alone special tools, but I do have a lathe and mill in the garage. I could cut the appropriate bolt down to size.


Deus Machina is offline  
    Reply With Quote
Sponsored Links
Advertisement
 
Old 03-20-2013, 07:22 AM   #2
RallieConGoggle
Focus Enthusiast
 
RallieConGoggle's Avatar
 
Join Date: Oct 2007
Fan#: 50774
Location: Lafayette, IN
What I Drive: 2007 CD Silver ZX4

Posts: 310
FF Reputation: 9 RallieConGoggle Good Standing Member
Buy-Sell-Trade Rating: (0)
http://www.focusfanatics.com/forum/s...ght=timing+pin

I would sell you mine if you can wait on shipping.
__________________
Rally with your goggles on!
2000 Pitch Black ZTS Auto (230,000+ miles)
2007 CD Silver ZX4 SES 5spd
Zetec Crew #190
RallieConGoggle is offline  
    Reply With Quote
Old 03-20-2013, 07:23 AM   #3
RallieConGoggle
Focus Enthusiast
 
RallieConGoggle's Avatar
 
Join Date: Oct 2007
Fan#: 50774
Location: Lafayette, IN
What I Drive: 2007 CD Silver ZX4

Posts: 310
FF Reputation: 9 RallieConGoggle Good Standing Member
Buy-Sell-Trade Rating: (0)
Also, here's my how-to with some pics of the tools I bought.
http://www.focusfanatics.com/forum/s...78#post2732278
__________________
Rally with your goggles on!
2000 Pitch Black ZTS Auto (230,000+ miles)
2007 CD Silver ZX4 SES 5spd
Zetec Crew #190
RallieConGoggle is offline  
    Reply With Quote
Old 03-20-2013, 07:27 AM   #4
Deus Machina
Focus Jr. Enthusiast
 
Join Date: Jun 2012
Fan#: 100167
Location: Brandon, FL
What I Drive: 2000 black ZX3

Posts: 38
FF Reputation: 1 Deus Machina Good Standing Member
Buy-Sell-Trade Rating: (0)
I've been reading through the how-to already. Good stuff. :)

I can't really wait, though. The car's in a parking lot of a building that is, thankfully, under renovation, but I doubt the owners want it there long.

I can manage this sort of thing with a screwdriver or the like if need by, but I'm well aware it will suck hard.
Deus Machina is offline  
    Reply With Quote
Old 03-20-2013, 07:34 AM   #5
RallieConGoggle
Focus Enthusiast
 
RallieConGoggle's Avatar
 
Join Date: Oct 2007
Fan#: 50774
Location: Lafayette, IN
What I Drive: 2007 CD Silver ZX4

Posts: 310
FF Reputation: 9 RallieConGoggle Good Standing Member
Buy-Sell-Trade Rating: (0)
The hole is kind of behind the CAT, so a screwdriver would be tricky.



__________________
Rally with your goggles on!
2000 Pitch Black ZTS Auto (230,000+ miles)
2007 CD Silver ZX4 SES 5spd
Zetec Crew #190
RallieConGoggle is offline  
    Reply With Quote
Old 03-20-2013, 09:20 AM   #6
sailor
"Elder"
 
sailor's Avatar
 
Join Date: Jun 2008
Fan#: 57268
Location: Williamsville, NY
What I Drive: 2004 Pitch Black ZTS 2.3 5spd.

Posts: 11,637
FF Reputation: 60 sailor Excellent Standing Member
Buy-Sell-Trade Rating: (0)
FWIW I think he means doing it by using the screwdriver down the plug hole to find TDC, wouldn't work to use one down the timing pin hole......

It's not like sticking a dial indicator down there, but you might be surprised how close you can get to exact TDC that way. Even with a dial indicator it takes a bit of back & forth wiggling to find the "center" of the piston's "dwell" at TDC. Fingers work quite well at feeling for the right spot.

If you need to do a "quick & dirty" belt replacement, where you leave the adjustable cam gears alone & just slide the belt on once you get the basic timing position for the crank & cams set up, the "screwdriver method" is adequate to get the cogs in the right notch & get the thing running!

Older engines weren't timed any better than the closest notch, and anyone who's done one of those would know how to get the Zetec timed that well.... Once the cam gears get their initial "set" at the factory, unless the engine has been rebuilt timing variations from a different belt will be minor. Nice to get it 'exact", but it should run fine with the original adjustment left alone. In fact, the "cam bar" is only NEEDED when you are resetting the cam gears since you can eyeball the cam position by the notches for the bar close enough to get the new belt in the right notch on the gear.

Certainly not as easy as when everything is locked in the right position, but certainly "doable".

Cheers!
sailor is online now  
    Reply With Quote
Old 03-21-2013, 06:31 AM   #7
amc49
Focus Fanatic
 
Join Date: Mar 2012
Fan#: 96610
Location: Fort Worth, TX
What I Drive: 00 wagon, 02 sedan both zetec atx

Posts: 4,219
FF Reputation: 23 amc49 Great Standing Member
Buy-Sell-Trade Rating: (0)
Amen brother. Loosening sprockets is what causes all the trouble, once you do then you can have partial tooth errors all over the place. Not loosening sprockets means you can only have full tooth errors which are much easier to see. The Ford procedure sets up the mechanic to have much more trouble to me. Then VCT confuses the issue even more.

The entire idea of the camtool is to get you merely right back where you were before you loosened sprockets to begin with. Silly.

If the timing belt teeth spacing was truly off virtually at all the maker would be out of business overnight. Those teeth have to be CLOSE to run at all well.
amc49 is offline  
    Reply With Quote
Old 03-21-2013, 06:42 AM   #8
RallieConGoggle
Focus Enthusiast
 
RallieConGoggle's Avatar
 
Join Date: Oct 2007
Fan#: 50774
Location: Lafayette, IN
What I Drive: 2007 CD Silver ZX4

Posts: 310
FF Reputation: 9 RallieConGoggle Good Standing Member
Buy-Sell-Trade Rating: (0)
Mine didn't line up perfectly with the bar, but I didn't bother adjusting the sprocket. I think that my intake is just a hair retarded now.
__________________
Rally with your goggles on!
2000 Pitch Black ZTS Auto (230,000+ miles)
2007 CD Silver ZX4 SES 5spd
Zetec Crew #190
RallieConGoggle is offline  
    Reply With Quote
Old 03-21-2013, 09:48 AM   #9
jasonbi
Focus Addict
 
jasonbi's Avatar
 
Join Date: Sep 2004
Fan#: 13305
Location: St John's, Canada
What I Drive: 2002 SVT

Posts: 579
FF Reputation: 3 jasonbi Good Standing Member
Buy-Sell-Trade Rating: (0)
if your hard up for the funds...use a metal file to lock the cam. thats how i did mine...came out perfect!
__________________
#3286 OF 4788
jasonbi is offline  
    Reply With Quote
Old 03-21-2013, 02:05 PM   #10
1turbofocus
FF Affiliate
 
1turbofocus's Avatar
 
Join Date: Oct 2003
Fan#: 1123
Location: Belmont, NC
What I Drive: 2000 ZX3 / 2002 SVT Turbocharged

Posts: 21,493
FF Reputation: 153 1turbofocus Excellent Standing Member1turbofocus Excellent Standing Member
Buy-Sell-Trade Rating: (28)
You dont need to buy the tools , I have built hundreds of Zetec engines and or heads and never used them
I use a file in the cams or you can get a flat bar and cut it from home depo and a screw driver in the #1 piston hole , get TDC and bar in and your good to go , your going to get a s close with this as with the tools , trick is to make 100% sure your at TDC

If your 100% TDC you will SLIGHTLY turn the engine each way and the screwdriver wont move , lock the came , install the best

Tom
__________________
Focus-Power: Your #1 Source for Ford Focus Speed, Tuning & Performance!

Customer Support
AIM: hpdyno
Email: hpdyno@aol.com
Phone: 704-249-3745
Site: focus-power.com

Elder 1turbofocus
1turbofocus is offline  
    Reply With Quote
Reply

Bookmarks & Social Networks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:21 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information : Site Map

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.