Oxygen Sensors, OL faults, and crazy volts - Page 3 - Focus Fanatics
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace



Go Back   Focus Fanatics > Ford Focus Tech Discussions > General Technical Chat

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
FocusFest Ford Focus Tire & Wheels FocusFanatics Merchandise

Reply
 
Thread Tools Display Modes
Old 01-21-2013, 08:38 PM   #21
SanduskySerpents
Focus Enthusiast
 
Join Date: Aug 2010
Fan#: 78065
Location: Va Bch, VA
What I Drive: 02 Silver Focus SE

Posts: 202
FF Reputation: 4 SanduskySerpents Good Standing Member
Buy-Sell-Trade Rating: (1)
When I rewired the o2 sensors they started functioning again. In all this mess I think I have solved it. Idle was ruff sounding like an overly aggressive camshaft were in it always about to die. I performed a smoke test after rewireing failed to fix everything and I found a that the EGR gasket failed catastrophically . After this I pressurized the cooling system a found 3 hoses leaking. Replaced gasket and hoses and it started idling 90% better. The unmetered air was causing it to go into open loop fault which just exasperated the problem.
SanduskySerpents is offline  
    Reply With Quote
Sponsored Links
Advertisement
 
Old 01-21-2013, 08:49 PM   #22
amc49
Focus Fanatic
 
Join Date: Mar 2012
Fan#: 96610
Location: Fort Worth, TX
What I Drive: 00 wagon, 02 sedan both zetec atx

Posts: 4,098
FF Reputation: 23 amc49 Great Standing Member
Buy-Sell-Trade Rating: (0)
Well I had that in there somewhere and redid my post since it wandered too much.

Sorry.

Point was, O2 sensor circuits are low voltage, when cut they need best connection possible, I've cut them before, preferable to solder them to prevent later humid conditions messing up the connection by corrosion, it doesn't have to be visible corrosion to cause trouble there.
amc49 is offline  
    Reply With Quote
Old 01-21-2013, 08:56 PM   #23
SanduskySerpents
Focus Enthusiast
 
Join Date: Aug 2010
Fan#: 78065
Location: Va Bch, VA
What I Drive: 02 Silver Focus SE

Posts: 202
FF Reputation: 4 SanduskySerpents Good Standing Member
Buy-Sell-Trade Rating: (1)
Yeah I didn't solder them but I did use heat shrink over the connectors to weather proof.
SanduskySerpents is offline  
    Reply With Quote
Old 01-21-2013, 09:41 PM   #24
goinloco1
Late for Dinner
 
goinloco1's Avatar
 
Join Date: May 2004
Fan#: 8529
Location: Aberdeen, SD
What I Drive: 13 stang

Posts: 15,206
FF Reputation: 90 goinloco1 Excellent Standing Member
Buy-Sell-Trade Rating: (2)
The downstream o2 does nothing but monitor the cat. If your getting wierd readings on it and your upstream your cat may be shot. your saying it runs like crap and isn't drivable also leads me this way.
By the way, stay away from bosch sensors, they are either crap right from the factory or burn up shortly. Definitely stay away from the bosch universals where you have to splice wires.
As was said, stick with oem.
goinloco1 is offline  
    Reply With Quote
Old 01-21-2013, 09:47 PM   #25
SanduskySerpents
Focus Enthusiast
 
Join Date: Aug 2010
Fan#: 78065
Location: Va Bch, VA
What I Drive: 02 Silver Focus SE

Posts: 202
FF Reputation: 4 SanduskySerpents Good Standing Member
Buy-Sell-Trade Rating: (1)
The erratic readings came from th OL fault and bad wiring. But it's fixed now. The car only has what I would call the usual stumble. It's not perfect but it runs
SanduskySerpents is offline  
    Reply With Quote
Old 01-21-2013, 09:59 PM   #26
goinloco1
Late for Dinner
 
goinloco1's Avatar
 
Join Date: May 2004
Fan#: 8529
Location: Aberdeen, SD
What I Drive: 13 stang

Posts: 15,206
FF Reputation: 90 goinloco1 Excellent Standing Member
Buy-Sell-Trade Rating: (2)
my bad, missed that post...lol
got to reading everything else and musta skimmed it.
goinloco1 is offline  
    Reply With Quote
Old 01-21-2013, 10:02 PM   #27
goinloco1
Late for Dinner
 
goinloco1's Avatar
 
Join Date: May 2004
Fan#: 8529
Location: Aberdeen, SD
What I Drive: 13 stang

Posts: 15,206
FF Reputation: 90 goinloco1 Excellent Standing Member
Buy-Sell-Trade Rating: (2)
May want to go to the parts store and grab a can of maf cleaner. May take care of some of the other problems or at least smooth them out some. no telling how long its been since its been cleaned last.
goinloco1 is offline  
    Reply With Quote
Reply

Bookmarks & Social Networks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:58 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information : Site Map

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.