Cosworth IM install - what a NIGHTMARE - Ford Focus Forum, Ford Focus ST Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus First Generation > DURATEC Performance (2003-2007)

DURATEC Performance (2003-2007) The place to chat about any Duratec 23, 23E, and 20 engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 10-21-2012, 02:27 PM   #1
AllCarFan
Focus Enthusiast
 
Join Date: Aug 2012
Fan#: 102583
Location: Atlanta, GA
What I Drive: 2005 Saleen Sonic Blue S121

Posts: 387
FF Reputation: 1 AllCarFan Good Standing Member
Buy-Sell-Trade Rating: (0)
Cosworth IM install - what a NIGHTMARE

Posting this for reference/search purposes and I have a question for those of you that have installed this item.

Now, I have been working and modifying cars and trucks for 16 years. Everything from engine and cam swaps, intake swaps, trans rebuilds, etc. The Cosworth intake manifold is the second worst install of any part that I have ever installed (first worst was a set of bassani equal length headers on a lightning).

First of all, the Cosworth instructions show how to install the manifold with the engine pulled. Well, any idiot can bolt on an intake with the engine out of the car....thanks for nothing Cosworth.

Note, if you have cruise control....like most focuses do....you need to modify or buy a special kit in order for you to retain cruise control. of course, this isnt in the instructions. They just say "call cosworth if you wish to retain cruise control with this intake." thats a crock of crap

Next: you are supplied with a 12mm brass button. Hmmmm, where does it go? Its no where in the structions. Oh, look there is a hole that is kind of threaded, but kind of not. Fast forward to an hour of research.....you tap this plug into that hole. again, nowhere in the instructions does it say to do this.

Next: since the cosworth intake eliminates the butterfly flaps on both 2.0 and 2.3 intake manifolds, you will be eliminating the vacuum hose assembly that controls these butterfly flaps. I belive there is a sensor that gets deleted also....and....you guessed it....not in the instructions.

Onto bolting on the intake.....good luck. Now, I know a lot of people have done this without issue. I am not one of those people. There is a sensor on the PS pump hose that the manifold will not clear. It is RIGHT up against the sensor. I had to use a screwdriver in order to get the holes lined up on the intake because I couldnt move the intake over far enough (this is on an 05 model).

The pcv bung supplied would not fit the tapped hole on the intake manifold. I tried and my friend tried. I had to cut the pcv bung and JB weld it to the intake. Let me say, that thing is never coming off now. Also, since you have to trim the PCV hose....disregard the instructions. I cut mine per the spec supplied...and even left it a little bigger. When I went to install it, it was over 1.5" short! I had to order a new hose.

I had to reshape the dipstick tube in order to get it to fit correctly.

There are three bolts that go on the bottom of the intake. The one near the throttle body is a piece of cake. The center bolt...well, I had to use a pair of needlenose pliers and gently get the bolt started. Then you can start to torque it down....about 1/16" of a turn at a time. But, at least you can get to it.
Now, the bolt near the PS pump has me at a complete loss. I have tried to get to it from every angle. I can barely see the hole, let alone get to it. The only way I can see to get to this is to completely remove the ps pump in order to get access to that bolt. Now, if that is the case, that is not in the instructions. If this must be done, its going to be an additional PITA because the PS fluid will have to be drained, hoses removed from hardline....because you cant access the bottom PS bolt unless you remove all of that.

So, here I sit. 5 bolts snugged down, but not tightened down with no way to get to the final bolt.

Had I known it would be this difficult, I would have taken it somewhere to install it.....or built my own custom sheetmetal intake.



So, does anyone know how to access the bolt near the PS pump?!


AllCarFan is offline  
    Reply With Quote
 

Bookmarks & Social Networks

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:20 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.