Hid not working on--

[Flying56eagle]

I have the Bi XENON For my 09, works great tell I try my brights, and blow a fuse every time, what do I need and please provide a link to were I can purchase the fix
Thanks

[Sponsor]

[Baldurs390]

check and see if you have water in any of the connection on the lights and ballast

[badazz2010focus]

they a high low kit?

[JDBug182]

Not familiar with the bi setup..... But are you running a fused relay from the battery?

[bmiglio72]

I used to have a bi xenon set....have the brights ever worked because if not its most likely the hi lo control box is defective so just send it back

[badazz2010focus]

most people dont run hi/lows because they lows are plenty unless you live out in the middle of cow country LOL!

[klrfoucs]

i have a set of hid's that i havent really seen elsewhere, from what i understand bi xenon have 2 filaments, mine only have a single that is about an 1in and a half long maybe a tad more but they magnetically pull back in the h13 socket so it gets higher and wider, terrible lighting on my high beams thought, recently my passenger side light has been turning yellow so i think my ballast is about to go and on occasion one or the other doesnt turn on but turn off and on again and they both work?

[bmiglio72]

I used to have the same thing. I'm sorry to say I really doubt that is a fixable problem. I think it may be the ballast taking a dump. I also have the thought it might be the high low control box in the wiring because both of your lights are acting up.

[crice8]

Sounds like there is a short somewhere in your Hid system. Hard to say where exactly. maybe in the ballast maybe just in a wire.

[Flying56eagle]

Originally Posted by Baldurs390

check and see if you have water in any of the connection on the lights and ballast

no water

Originally Posted by badazz2010focus

they a high low kit?

yes that is why the are called BI exon

Originally Posted by JDBug182

Not familiar with the bi setup..... But are you running a fused relay from the battery?

No I'm not, that is what I was woundering, because I blow the fuse every time, if I install the facktory set back everything works fine, when I install the hid. everything works also ecept the brights

Originally Posted by bmiglio72

I used to have a bi xenon set....have the brights ever worked because if not its most likely the hi lo control box is defective so just send it back

this is my second set..

Originally Posted by badazz2010focus

most people dont run hi/lows because they lows are plenty unless you live out in the middle of cow country LOL!

in pa for the inspection you have to have high and low beam switch working.

Originally Posted by klrfoucs

i have a set of hid's that i havent really seen elsewhere, from what i understand bi xenon have 2 filaments, mine only have a single that is about an 1in and a half long maybe a tad more but they magnetically pull back in the h13 socket so it gets higher and wider, terrible lighting on my high beams thought, recently my passenger side light has been turning yellow so i think my ballast is about to go and on occasion one or the other doesnt turn on but turn off and on again and they both work?

glad you found your problem..

Originally Posted by bmiglio72

I used to have the same thing. I'm sorry to say I really doubt that is a fixable problem. I think it may be the ballast taking a dump. I also have the thought it might be the high low control box in the wiring because both of your lights are acting up.

it never worked for the start. second set

Originally Posted by crice8

Sounds like there is a short somewhere in your Hid system. Hard to say where exactly. maybe in the ballast maybe just in a wire.

again second set.. So no has a fuse system I gather from the responses, and everyone seams to just buy the single cheaper one filament hids, and never use there brights anymore? am I missing something here. Maybe I will just put my factory system back in.