2.3 MTX-75 Bolt pattern - Focus Fanatics
Focus Fanatics Ford Focus Forums
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace



Go Back   Focus Fanatics > Ford Focus Tech Discussions > General Technical Chat

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
FocusFest Ford Focus Tire & Wheels FocusFanatics Merchandise

Reply
 
Thread Tools Display Modes
Old 10-01-2012, 04:41 PM   #1
gmardiro
Focus Rookie
 
Join Date: Nov 2004
Fan#: 15962
Location: Boston
Posts: 4
FF Reputation: 1 gmardiro Good Standing Member
Buy-Sell-Trade Rating: (0)
2.3 MTX-75 Bolt pattern

Does anyone have or know where to find a bell housing bolt pattern for an 2.3L manual MTX-75? The dealer wasn't helpful. I have the old transmission out and rebuilt one in but one or two of the bolts don't seem right. One in particular is too long for any particular hole. Amateur move I know but I had them out in a sequence in a piece of cardboard. Not sure what the heck happened.

Any help is appreciated.

2003 2.3L Manual zx5


gmardiro is offline  
    Reply With Quote
Sponsored Links
Advertisement
 
Old 10-01-2012, 04:51 PM   #2
whynotthinkwhynot
Captain TMI
 
whynotthinkwhynot's Avatar
 
Join Date: Jan 2005
Fan#: 18416
Location: the armpit of TN, Memphis, TN
What I Drive: 05 ZXW; 02 Windstar; 13 C-Max SEL

Posts: 19,803
FF Reputation: 267 whynotthinkwhynot Outstanding Standing Memberwhynotthinkwhynot Outstanding Standing Memberwhynotthinkwhynot Outstanding Standing Member
Buy-Sell-Trade Rating: (1)
Well then, take a measuring tape to the center of the holes on the old one and one to the one installed in the car. I always used a fabric tape- like what is used for measuring sewing projects. Then you can put it around the trans and measure the distances between all of the holes at once- example: 1= 1", 2=6", 3=11" and so on. Then you can wrap that same tape around another transmission to see if the centers of the holes line up with what you measured on the other more easily than measuring the distance between each set of holes.
__________________
Be eclectic.
---The Complete How-To Archive--

Moderating everything now, let me know if I can help.

Quote:
Originally Posted by the user formerly known as ZX3_Chick View Post
You're special aren't you.
whynotthinkwhynot is offline  
    Reply With Quote
Old 10-01-2012, 07:25 PM   #3
gmardiro
Focus Rookie
 
Join Date: Nov 2004
Fan#: 15962
Location: Boston
Posts: 4
FF Reputation: 1 gmardiro Good Standing Member
Buy-Sell-Trade Rating: (0)
I think I follow, but how does that help me ensure the right bolt goes in the right spot? That's what I'm really looking for. I figured a bolt pattern might show the hardware that goes into each location.
gmardiro is offline  
    Reply With Quote
Old 10-02-2012, 01:32 PM   #4
sailor
"Elder"
 
sailor's Avatar
 
Join Date: Jun 2008
Fan#: 57268
Location: Williamsville, NY
What I Drive: 2004 Pitch Black ZTS 2.3 5spd.

Posts: 9,102
FF Reputation: 57 sailor Excellent Standing Member
Buy-Sell-Trade Rating: (0)
I've seen parts diagrams that detailed, but unfortunately only for motorcycles (Honda for example).

The Ford computer parts diagrams I've seen are VERY poor in that regard, for example i had to find a part number in this forum for my wiper relay since the dealer's parts diagram simply listed all the relays in that area by part number without describing the function or location of ANY of them!

The parts person mentioned that the only way he can tell which one is needed is for a mechanic to pull the old one to match numbers!

When facing an issue like yours, my usual approach is to loose fit all the bolts looking for similar amount of shank exposed when they are only screwed in one turn. Which goes where usually becomes obvious.

Did the ones installed so far seem to tighten up properly?

Sometimes when a bolt has to go through a couple parts you can get a false sense of the proper length when it screws into an unthreaded intermediate piece instead of the threaded hole in a part further in.

Using a small rod to check hole depth can determine if this is happening to you.

I'm betting this is what's happening, and the long bolt belongs in one of the holes a shorter one is in now....

Luck!
sailor is offline  
    Reply With Quote
Reply

Bookmarks & Social Networks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:50 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information : Site Map

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX. You can find all Ford Focus related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.