How to: Tail light tint - Focus Fanatics
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace



Go Back   Focus Fanatics > Ford Focus Third Generation > MK3 Focus

MK3 Focus The place to chat about general questions, window tinting, exterior body, interior and lighting upgrades for the third generation 2012-Current Focus.

Search This Forum | Image Search | Advanced Search    
FocusFest Ford Focus Tire & Wheels FocusFanatics Merchandise

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 09-15-2012, 03:56 AM   #1
Chickenmuffn
Focus Enthusiast
 
Join Date: Sep 2012
Fan#: 103458
Location: York, United Kingdom
What I Drive: 2011 Focus Zetec 1.6

Posts: 76
FF Reputation: 9 Chickenmuffn Good Standing Member
Buy-Sell-Trade Rating: (0)
How to: Tail light tint

NOTE: Following was done on a Euro 2011 Ford Focus Hatch MK3

**If you find that you tinted too much, you can reduce the tint by rubbing away with rubbing compound. This will slowly take off tint until you are happy!**

I used the following products:

Basic tools
1500 grit wet/dry sand paper
Paint thinner
Wax and grease remover
VHT Nite shades
Acrylic lacquer clear coat
Meguiar's ultimate compound



1a.) Remove tail lights, there are 2 wing nuts and a clip that have to be undone. The wing nuts are located here:



And they look like this:



Once the wingnuts are removed, pull the tail light sideways off the car, and the clip should come out. Look at the following picture and take note at where the clip is. Circles are the wingnut bolts, and the square is the clip.



1b.) Remove hatch light

Just unscrew the two screws indicated, and disconnect the wires at the back.



1c.) Remove the 2 lower rear reflectors. They are held in by clips which go though the rear bumper. Just stick your head under the car and use pliers to undo the clips.






2.) Wet sand the tail light with 1500 grit



3.) Wash off the debris with paint thinner and a cloth. Rub down the tail light firmly after, as it can leave a film.



4.) Apply wax and grease remover as the final prep, careful not to touch or move the tail light after this step.



5.) Apply VHT Nite shades and clear coat. I used quick fanning motions with the VHT nite shades and the clear coat. I used 3 coats of nite shades and 4 coats of clear.



6.) After spray let cure for at least 12 hours, 24 is best. Buff with rubbing compound until smooth and shiny.

Before rubbing compound:



After rubbing compound: (had to use the car, so cut the buffing process short, i'll finish it up later)



7.) Reattach lights. (Looks darker than it is, car was in a shadow.)





8.) Rubbing compound more once attached, you can really put your back into it when the lights are on the car. I also used a synthetic polish to give it a bit more shiny. This is the end product. I'm quite happy with it.





Last edited by Chickenmuffn; 09-15-2012 at 11:07 AM.
Chickenmuffn is offline  
    Reply With Quote
 

Bookmarks & Social Networks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:24 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information : Site Map

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.