HOW TO: Wiring in Illuminated Door Sills - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace

Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Second Generation > MK2 Focus

MK2 Focus The place to chat about general questions, window tinting, exterior body, interior and lighting upgrades for the second generation 2008-2011 Focus.

Search This Forum | Image Search | Advanced Search    
FocusFanatics Merchandise

View Poll Results: Was This Helpful?
Yes, I appreciate it and want to add these to my car 19 95.00%
No, I know less now than before 0 0%
Your thread is bad and you should feel bad! 1 5.00%
Voters: 20. You may not vote on this poll

Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 04-14-2012, 06:52 PM   #1
Focus Addict
DarderSauce's Avatar
Join Date: Feb 2012
Fan#: 95564
Location: Blaine, MN
What I Drive: '08 Vermillion Red 5 speed SEdan

Posts: 1,093
FF Reputation: 5 DarderSauce Good Standing Member
Buy-Sell-Trade Rating: (2)
HOW TO: Wiring in Illuminated Door Sills

Here we go everyone, in response to VonKrause's How to wire in fog lights that I found very helpful, I wanted to help anyone considering installing illuminated door sill plates. First thing is first, go get yourself the Ford Sill kit..... I got mine from another member and it was $100. If you buy them from Ford they usually run you around $200 but you can usually find them on Ebay or check the marketplace.

this is what they will look like:

Illuminated Sills by DarderSauce, on Flickr

First thing you are going to want to do is remove the battery terminals (+ & -)

Next you are going to want to remove the factory sill plates..... Just snaps right off.

3 by DarderSauce, on Flickr

Then your passenger side kick panel

2 by DarderSauce, on Flickr

4 by DarderSauce, on Flickr

Now remove your A pillar

6 by DarderSauce, on Flickr

5 by DarderSauce, on Flickr

8 by DarderSauce, on Flickr

This is where you will be wiring in your Sill plates

7 by DarderSauce, on Flickr

Unplug the connector and find the grey/violet wire

9 by DarderSauce, on Flickr

Strip back some of the electrical tape so you can use a quick connector to splice in the wiring for the lights.... You will connect the red wire to the grey/violet wire (the black wire is the ground but we will get to that later)

13 by DarderSauce, on Flickr

12 by DarderSauce, on Flickr

Now you are going to want to strip the black wire back so you can attach an end to it and ground it on a bolt under the kick panel (any bolt will do). But since I had only large ends I had to double the wire over so there was more metal connecting to the end I connected

14 by DarderSauce, on Flickr

16 by DarderSauce, on Flickr

Now you have to feed the wire from the passenger side to the drivers side. I fed it as far back as I could so they would not be in the way. This is where a coat hanger/metal wire comes in. Feed the wire through from the drivers side and hook it to the wiring for the door sills so you can bring it back through.

18 by DarderSauce, on Flickr

I ran the wire on top of this metal bracket

29 by DarderSauce, on Flickr

Now you can remove your sill and kick panel on the drivers side door

19 by DarderSauce, on Flickr

You can now drill the holes on the kick panels, make sure you do not drill into the clips that attach the sills to the body. The position you drill will depend on the side you are on.

21 by DarderSauce, on Flickr

20 by DarderSauce, on Flickr

Next thing you are going to want to do is center the Illuminated Sills on the factory sills and tape off the end and the middle of where you want them.

22 by DarderSauce, on Flickr

Next you want to clean the door sills with the alcohol pads (in kit) and apply the adhesive promoter (also in kit) and let the promoter sit for 5 min.

23 by DarderSauce, on Flickr

Now you are ready to attach the plates!!! Remove the tape from the back of the plates and line them up with the lines you have taped off, this is also when you will feed the fiberoptic wire in the holes you drilled. After attaching the sills they will look like this

28 by DarderSauce, on Flickr

Attach the battery terminals and make sure everything lights up and if it it does... re-assemble everything and you're done! Hope this helps and I will be happy to answer any questions you guys may have.

If you can't wear it out, burn it off

Last edited by DarderSauce; 04-22-2012 at 09:26 AM.
DarderSauce is offline  
    Reply With Quote

Bookmarks & Social Networks

Quick Reply

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 09:41 AM.

Copyright 2002-2014 All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat