custom airbox/heat shield for 2012 steeda SRI - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Third Generation > DURATEC Ti-VCT Performance (2012-Current)

DURATEC Ti-VCT Performance (2012-Current) The place to chat about any Duratec 2.0L Ti-VCT engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 04-13-2012, 02:41 PM   #1
darkangelism
Sonic Crew #04
 
darkangelism's Avatar
 
Join Date: May 2011
Fan#: 85425
Location: oklahoma city, OK
What I Drive: 2012 Focus Titanium Hatch

Posts: 7,395
Points 4,324, Level 41
Points: 4,324, Level: 41 Points: 4,324, Level: 41 Points: 4,324, Level: 41
Level Up 87% Completed
Level up: 87% Level up: 87% Level up: 87%
Forum Activity 6%
Activity: 6% Activity: 6% Activity: 6%
FF Reputation: 9 darkangelism Good Standing Member
Buy-Sell-Trade Rating: (0)
custom airbox/heat shield for 2012 steeda SRI

I am planning on trying to build a custom airbox/ heat shield for the Steeda Short Ram intake for the 2012. It is somewhat similar to their cold air intake but uses all of the stock inlets and allows for a cold air pipe from the front bumper area, similar to the mod that newmission did. I am looking for some feedback and see if there are any flaws in my design. The airbox will be built from 1/8th inch aluminum sheet bent into the proper shape.

Front panel mod:
Taking what newmission did with drilling holes in the front plastic triangle and making full slots across with the exception of where the punchouts are. I will then hot glue a piece of screen door screen to the backside, this will help keeps bugs and rocks from getting sucked up.

I will hot glue a funnel that is cut to the right size to the first piece of intake pipe and wrap the edge with duct tape so that no air can escape out and to protect the glue from weather. The first piece of pipe will a 45 degree mandrel bent pipe 2.5” inside diameter, and will be hose clamped to a 1 foot long straight pipe and will run into the airbox.

Airbox:

The airbox will be four sided liked the CAI that Steeda has, and have a 2 sided cover. The estimated dimensions are six inches wide, six inches long and 7 inches tall. The bottom piece will be an extra half inch long on the open right side to make the connection piece to the chassis shorter. That piece will screw in below the grounding wire, in the same spot that the steeda design uses.
The bottom side will have a hole for the 2.5” pipe along the top edge so that the pipe can be anchored in the box with a hose clamp that is screwed into the box. It will also have a screw hole to screw the stock steeda SRI mount to.
The front side will have a hole for the modified second stock inlet and will have a bracket that runs to the chassis to attach below that hose.
The left side will have a hole on the bottom edge for the primary stock intake with the hole for the velocity stack right above it, this is basically the same design that steeda uses and the velocity stack will be screwed into the aluminum like the steeda design. Next to that hole will be another bracket like the steeda has for a 3rd mount point to the chassis.

Stock air inlet mod:
The stock air inlets have two inlet hoses. The first one will be the same as the steeda design. The second inlet the steeda design just plugs it, probably due to the odd shape, the hole on the chassis side is round and I will take some hose and screw it into the housing to allow a round shape into the airbox. This should allow for three separate inlets to the airbox and higher and colder airflow.

The top cover:
The top cover will be an L shape piece of aluminum that will use two screws on the left side to hold it in place. The top will be covered with some foam that will prevent rubbing against the hood.

Parts list:
24X24 1/8 inch thick aluminum(airbox)
12X24 1/8 inch thick aluminum(cover)
1 foot 45 degree aluminum pipe 2.5” inner diameter
1 foot straight aluminum pipe 2.5” inner diameter
1 pipe connector
Screen door mesh
Funnel
2 inch inner diameter hose for 2nd inlet
Three metal brackets
12 8mm screws and bolts
Steeda short ram intake
Foam padding











Last edited by darkangelism; 04-13-2012 at 11:31 PM.
darkangelism is offline  
    Reply With Quote
 

Bookmarks & Social Networks

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:45 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat