How To: Change SVT Gauge Color - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus SVT > SVT Interior Mods & Upgrades

SVT Interior Mods & Upgrades The place to chat about general questions, window tinting, exterior body, interior and lighting upgrades for the 2002-204 SVT Focus.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 11-15-2010, 03:04 PM   #1
mtothaj
Focus Enthusiast
 
Join Date: Aug 2010
Fan#: 77917
Location: Fort Smith, AR
What I Drive: 2003 SVT ZX5

Posts: 134
FF Reputation: 6 mtothaj Good Standing Member
Buy-Sell-Trade Rating: (3)
How To: Change SVT Gauge Color

I did this write up to help any svt owners who hate the stock green color of their gauges and odometer. I went with red but any color could easily be used. Materials used are 1 white sheet of printer paper size 8.5 X 14 inch and 1 colored transparency sheet of equal length. Tools needed are Phillips screwdriver, flat head screwdriver, 7mm socket wrench, T-10 socket,razor blade, scanner, photoshop(or equivalent photo editing software), and a printer. I am not responsible for any damage to your vehicle. This how to covers the steps for the main instrument cluster. The same steps apply towards the small gauges on the right.

1. Remove the 3 screws holding the trim piece covering your gauges.


2. Push in the two tabs on either side of the steering column. This releases the trim piece connected to the gauge cover.


3. Disconnect the hatch release button.


4. Use the 7mm socket to remove the four bolts holding the instrument cluster in place.

5. Remove the clip on top of the instrument cluster(this is the power source that lights up the gauges.) Separate that piece from the gauges by pushing a flat head under the plug and sliding to the right


6. Remove the main harness located on the back of the cluster. Slide the black bar all the way to the left and pull out.


7. Separate the black cover piece from the white gauge housing by lifting up on the four tabs(two on top and two on bottom)

8. Remove the 3 black plastic tabs that hold the tach needle and speedometer needle in place when the vehicle is turned off. These pieces pull straight off. Also remove the needles by pulling directly up.

9. Remove the 3 torx bolts holding the gauges in place. Once these are removed the gauges lift straight out.

10. Remove the plastic piece that interacts with the odometer from the underside by squeezing it together and pushing it out.


11.You then separate the gauge face from the back white part that actually lights up.


12. The gauge face is what you scan. Using a photo editing software edit the gauges to whatever you want them to look like. I enlarged the svt logo and deleted the kph. Also you need to delete the background(the gray part of the gauges) so when it is printed all that prints out are the numbers and lines. The gauge is larger than a normal piece of paper so use 8.5x14 inch paper.

13. Using the stock gauges as a template cut the new printed gauges out including all holes and the rectangle where the odometer is seen.

14. Use the stock gauges again to trace out that same shape onto the transparency sheet of your color choice (I went with red to match my seat inserts.)

15. You will have to cut your stock gauges to install the High beam light, abs light and traction control light. Once cut from your stock gauges install them directly on the white part of your gauges that light up. You will also have to cut away these sections from your new gauges and transparency sheet.

16. Install the new gauges on top of the transparency sheet and then those two pieces go on top of the white part of you gauges that light up.

17. Now you can put everything back together in reverse order.

18. to calibrate your needles use this. http://www.focusfanatics.com/howtos/needlecalibration/

Thanks, I hope everything goes well. Soon to follow will be how i did my odometer.


mtothaj is offline  
    Reply With Quote
 

Bookmarks & Social Networks

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:44 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat