How-To Retro-Fit Stock Headlights W/Projectors - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace

Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > MK1 Focus

MK1 Focus The place to chat about general questions, window tinting, exterior body, interior and lighting upgrades for the first generation 2000-2007 Focus.

Search This Forum | Image Search | Advanced Search    
FocusFanatics Merchandise

Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 06-29-2008, 07:43 AM   #1
Join Date: Jun 2005
Fan#: 24432
Location: Bowling Green, Ky
What I Drive: 2002 Stealth ZX3

Posts: 4,142
FF Reputation: 91 Sn4ckM4st3r Excellent Standing Member
Buy-Sell-Trade Rating: (4)
How-To Retro-Fit Stock Headlights W/Projectors

This will be updated weekly i would say with new types of headlights fro different cars i will be doing. As well as pics added when the cam makes it back.

Retro-Fitting Stock Headlights w/Projectors-

10 Torx
Flat Head Screwdriver
Dremel w/cutting head
Saftey glasses

Stock Headlights
Projectors(E55's, Acura TSX or TL, Audi RS6)
JB Weld
Sheet Metal (optional fitting)
Clear Silicone Sealer.

Optional Materials-
1000 Grit Sandpaper
Paint your choice of color if you want to paint the headlights.
Washers to prefrom optional Projector modification (more color on the Cut-off)
Headlight Restore kit (if your lenses are crapped)
Projector Shroud

Taking headlights apart-
Preheat your oven to 250 degrees.
Load one headlight into the oven on a cookie sheet or something similar for 10-15 minutes.
Remove at about 10 mins to check glue seal if not all the way stick back in to loosen completely.
One glue seems to just pull apart, use flat head screw driver to pry parts if needed.
Clean glue you will be replacing and using new sealer later.

Preparing for you Projector of Choice-
*This part will depend HUGELY on which projector you will want and what style headlight you will be after.*

OEM Fitting- !*Make sure to wear a mask and saftey glasses while cutting this stuff makes alot of dust and is not fun to get hit by.*
Once the headlight is apart first remove the Screw behind the housing holding in the Bulb Shield.
depending on your projector choice you will need to measure you prjector and then use the dremel to cut a spot from the stock reflector to fit it.
After you have cut this opening clean off the area and then test fit to make sure it will go into the hosuing.
Using a small piece of sheet metal cut into a square place it on the back of housing over the hole. Find a suitable mounting spot and then secure it to the housing with a few screws and some jb weld.
Once again test fit your projector inside of your mounting plate as well your hosuing to assure its level and is secure.

While apart use the shroud you have chosen to measure and then cut to be placed inside around the projector.

JBweld it all and let sit for approx 6 hours.

Preparing the OEM Fit for a test run-
At this point your Jbweld should have fully cured
After your JBweld has had time to cure take both lens and housing and line with silicone.
Put them back together assuring that each and every space is filled to prevent water or condensation build up.
Let your silicone sit for a couple hours and come back.
Take both Headlights and prepare to reinstall in car to check projector clearence.
Find a set of bulbs or HID's if thats what you will be using and prepare them for a run.
Wait till dark and find a flat surface thats about 15-20 ft from you.
Put the HID's in and adjust headligthts to get a crisp flat cutoff.

If you want a little more Blue out of your cutoff and are willing to sacrifice Cutoff sharpness. YOu will need 1-3 #8 washers for the acura projectors. Installing these to lengthen the shield distance will give you a bit more blue.

*Optional Painting*
While the headlights are apart if you would like to paint your headlights to match the vehicle this is the time.
Use the 1000 grit to rough up the chrome pieces really easy to do.
Hit with a few coats of evenly sprayed paint of your choice.
Use a clear as well to prevent and kind of cracking or anything.
Wait to cure and dry reinstall.

Aftermarket Look-
Following the taking apart of the headlights you will need to remove the rear reflector piece.
To do this both plastic peices jsut pop off.
The off white with force can be taken out via the back.
Seal the hole off with silicone or a similar sealing agent.
Once the rear reflector and shield are out remove any spare pieces with the dremel making sure to wear your saftey objects.
Depending on how you want it to look use bondo or fiberglassing to fill in the area to give amore full look to the head light.
Paint your front piece a color of your choice or remove from the headlight.
After you have chosen your style put back together. and continue with the test.

I do have pictures but my camera is in New Hampshire so i will have what i don't have here for everyone. And be sure to watch this as it will be updated frequently with more methods and things
I am looking to try and install some sort of niteshaded parking lamp inside. And may be testing a ST170 Retro fit soon.

Test fit-

Example Cutoff-

Tons more pictures for each segemnt to come.

Also a KEY NOTE!!! I suggest anyone who tries to take this on also look into an eyebrow setup. It will make your car look MUCH better and more agressive here is my test eyebrow.


Last edited by Sn4ckM4st3r; 07-01-2008 at 02:47 PM.
Sn4ckM4st3r is offline  

Bookmarks & Social Networks

Quick Reply

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
03 Stock headlights and Grill. NOT SVT HEADLIGHTS *CLOSED* jlemond Archive 6 02-09-2007 03:17 AM
Stock '02 headlights -not SVT $50 for the pair J-Dawg Archive 22 03-31-2006 10:24 AM
Changing Stock Headlights for Halo? Jojos ZTS Focus MK1 Focus 1 03-10-2006 10:12 AM
will stock 16's fit svt hatchd03 Wheels & Tires 5 07-22-2004 02:05 PM
Wings West Front Air Dam, 2000 Focus stock bumper, 2000 Focus stock suspension sale! meanpiolin Archive 0 07-10-2004 03:51 PM

All times are GMT -5. The time now is 12:10 PM.

Copyright 2002-2014 All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat