Focus Fanatics Forum banner

Official ST Part Numbers Thread

29K views 33 replies 15 participants last post by  eglove 
#1 · (Edited by Moderator)
This thread will be to list all part numbers found for the 2013+ Focus ST. As more are discovered, please post them in here and I will update the original post as often as I can.

I won't promise that everything posted will be guaranteed to swap onto a non-ST 2012+ Focus, but that will be discovered with time.

Parts are organized alphabetically within the categories below.

- - -

Exterior

Badge (ST) - CM5Z-5842528-A
Fog Light Inserts for Front Grille - 17B814
Front Bumper Cover - 17D957
Front Bumper Grille - 17B968
Fog Light Inserts for Front Grille - 17B814
Front Bumper Grille Insert (Bottom Piece) - 17K945
Rear Body Reflector Assembly (RH and LH) -13A565
Rear Bumper Black Insert (RH and LH) - 17D752
Rear Bumper Extension ST Version - 17810

ST front-end conversion part numbers: http://www.focusfanatics.com/forum/showthread.php?t=305741

Bumper cover: CM5Z 17D957 BBPTM
Upper Bracket: CM5Z 17C897 B
Left Foglight Grill: CM5Z 17E811 A
Right Foglight Grill: CM5Z 17E810 A
Lower Grill: CM5Z 17K945 A
Main Grill: CM5Z 8200B A
Ford Emblem: CV6Z 16605 A
ST Emblem: CM5Z 5842528 B
Air Dam: CM5Z 8310 D
Air Deflector: AM5Z 17626 A


Interior

Drivetrain

Suspension/Wheels/Brakes

Front Coil Springs - CV61-5310-SG
Front strut (LH) - AST-12281
Front strut (RH) - AST-12287
Rear Coil Springs - CV61-5560-SG
Rear shock - ASH-24518 (include upper shock mounts/bumpstops) [DOES NOT fit non-STs]
Upper front strut mount - AD-1098
 
See less See more
#4 ·
Would it be possible to get this stickied, for everyone's reference?
 
#8 ·
Here are some specs out of the ST manual. Besides the struts, it looks like Ford made changes to the knuckles and stabilizers too.

•2.0L GTDI EcoBoost I4 engine
•Over boost function for increased torque
•Electronic over-rev function with 6800 rpm redline
•ST tuned 2.5 in. center exit exhaust system
•Getrag-Ford MMT6 6-speed manual transaxle
•Active sound symposer
•Variable ratio steering
•Modified front suspension knuckle for improved wheel end geometry
•Cast rear knuckle (improved stiffness) and alternative anti-roll-bar
mounting for improved efficiency
•ST tuned springs and dampers
•Increased diameter (320 mm) front brake rotors and unique calipers
with ST tuned pad formulation front and rear
•Enhanced torque vectoring control with cornering under steer control
•ST tuned electric power assisted steering with torque steer compensation
•AdvanceTrac stability enhancement system with three modes:
Normal, Sport and Disabled
•18in.x8in.55mm offset aluminum ST Wheels
•P235/40-18 directional Goodyear Eagle F1 tires
•ST engineered front and rear fascias and rear wing
Focus ST Unique Features
 
#19 ·
All from fordparts.com
http://www.fordparts.com/Commerce/CatalogResults.aspx?y=2013&m=Ford&mo=Focus#Search

17810 - Rear Bumper Extension ST Version - $239.50
17D752 - Rear Bumper Black Insert (RH and LH) - $38.47
13A565 - Rear Body Reflector Assembly (RH and LH) - $305.33 (seems steep)

I'm not gonna bother listing all the mounting hardware for these, visit the webpages.
Added, thank you!

Also, I want to note that the rear shocks come with the upper shock mounts/bumpstops.
Also added, thanks again Zillon!
 
#10 ·
#12 ·
True, but this would also be for those who just want a couple ST parts on a regular Focus, or perhaps want an ST-inspired version in a configuration that can't be ordered, i.e. a sedan.

Thanks for the new numbers, I'll update the original post when I'm not on my phone.
 
#18 ·
You are still talking over $1,000 for just some of the body covers. Maybe some one will produce some aftermarket parts that will look nice and at a lesser cost. As far as the exhaust, Borla has a Catback system for both the Sedan and Hatch 2012's and their systems do not have any DRONE. I made the mistake of buying a Magna Flow catback system and it had terrible drone at around 65 to 70 mph and ended up taking it off of my 2009 Edge. It did sound very mellow but the drone was bad! The catback system I had bought for my 2011 Mustang GT was the tourning system and really sounded great with no drone at all.
 
#20 ·
I just had my Headlights out and put in some of those switchback LED blinker bulbs. You know, the 2012 Mustang's headlamp housing is the same on both HID and Non-HID cars. The ballast is actually inside the Headlight housing and all you do is plug in the power for them and the blinker cord. I know there will be issues with the bulb monitoring system and maybe the Hi-Lo beam stuff but maybe the ST's have a separate Halogen High Beam bulb. Once the cars actually come out, maybe someone can look into this and see if they can be wired to work in a regular Focus.

Just a note: In case anyone puts those "50 watt 6 ohm" resistors in to simulate the load of a regular lamp for LED replacements, be sure to mount them to a flat metal surface as they get really hot if say you leave your emergency flashers on for a while. I ended up using an old computer system CPU cooler aluminum finned heat sink and modified it to mount inside my fender area and then screwed the resistor to it with that heat sink compound as to help dissipate some of that heat. Before I did that, you could not touch the resistor without welders gloves on but after the mod, the resistors were hot but you could touch them bare handed without getting blisters.
 
#21 ·
WOW! I just priced the HID headlight assembly for just one side of a 2011 GT500 and it is $1180..58. Tousley Ford still wants $779.19 for each side. Very cost prohibitive to use the factory parts I guess.
 
#24 ·
Added, cheers!

Rear shocks will NOT work with our Foci without upgrading the rear spindle and associated parts. Shock is much shorter and connected to a different mounting location.
Noted on page one, that's unfortunate. [V]
 
#29 ·
ST front-end conversion part numbers: http://www.focusfanatics.com/forum/showthread.php?t=305741

Bumper cover: CM5Z 17D957 BBPTM
Upper Bracket: CM5Z 17C897 B
Left Foglight Grill: CM5Z 17E811 A
Right Foglight Grill: CM5Z 17E810 A
Lower Grill: CM5Z 17K945 A
Main Grill: CM5Z 8200B A
Ford Emblem: CV6Z 16605 A
ST Emblem: CM5Z 5842528 B
Air Dam: CM5Z 8310 D
Air Deflector: AM5Z 17626 A


EDIT: I cannot update the original post with these. Perhaps a moderator can help?
 
#33 ·
This thread will be to list all part numbers found for the 2013+ Focus ST. As more are discovered, please post them in here and I will update the original post as often as I can.

I won't promise that everything posted will be guaranteed to swap onto a non-ST 2012+ Focus, but that will be discovered with time.

Parts are organized alphabetically within the categories below.

- - -

Exterior

Badge (ST) - CM5Z-5842528-A
Fog Light Inserts for Front Grille - 17B814
Front Bumper Cover - 17D957
Front Bumper Grille - 17B968
Fog Light Inserts for Front Grille - 17B814
Front Bumper Grille Insert (Bottom Piece) - 17K945
Rear Body Reflector Assembly (RH and LH) -13A565
Rear Bumper Black Insert (RH and LH) - 17D752
Rear Bumper Extension ST Version - 17810

ST front-end conversion part numbers: MK3 to ST front end conversion part numbers! - Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum

Bumper cover: CM5Z 17D957 BBPTM
Upper Bracket: CM5Z 17C897 B
Left Foglight Grill: CM5Z 17E811 A
Right Foglight Grill: CM5Z 17E810 A
Lower Grill: CM5Z 17K945 A
Main Grill: CM5Z 8200B A
Ford Emblem: CV6Z 16605 A
ST Emblem: CM5Z 5842528 B
Air Dam: CM5Z 8310 D
Air Deflector: AM5Z 17626 A


Interior

Drivetrain

Suspension/Wheels/Brakes

Front Coil Springs - CV61-5310-SG
Front strut (LH) - AST-12281
Front strut (RH) - AST-12287
Rear Coil Springs - CV61-5560-SG
Rear shock - ASH-24518 (include upper shock mounts/bumpstops) [DOES NOT fit non-STs]
Upper front strut mount - AD-1098


Awesome
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top