Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum

Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum (http://www.focusfanatics.com/forum/index.php)
-   MK1 Focus (http://www.focusfanatics.com/forum/forumdisplay.php?f=45)
-   -   How to: Paint your Headlights 2005 (http://www.focusfanatics.com/forum/showthread.php?t=59986)

HeelToe 09-20-2005 09:58 PM

How to: Paint your Headlights 2005
 
Ok well as I said I would I'm making this write up for painting the inside of your 2005 Focus headlights black.

Materials needed:

Black paint (recommend gloss finish)
Silicone Sealant
Scour pad
Beer [;)]
Masking tape
Tools needed:

10mm wrench
8mm wrench
Phillips screwdriver
Flathead screwdriver
torx bits (allens will work but torx will be better)
Car jack
Your hands
Razor Blade

Time require:
Total - 12-48hrs
Headlight removal - 30min - 1hr
Headlight opening - 2-3hrs
painting - 2-3 hrs
paint dry time - at least 1hr
Headlight reassembly - 30min - 1hr
Sealant cure time - at least 8hrs
headlight reinstall 30min - 1hr

Step 1

Using a Phillips screwdriver Remove the Black plastic radiator shroud.

http://www.focusfanatics.com/howtos/..._2041small.jpg

Step 2

With a 10mm wrench loosen the two bold hold the upper grill to the radiator frame. Then while pulling forward lift the two clips on either side of the hood latch to remove the upper grill.

http://www.focusfanatics.com/howtos/..._2042small.jpg

Step 3

Using a 10mm wrench loosen the top two bold on the headlight assembly.

http://www.focusfanatics.com/howtos/..._2043small.jpg

Step 4

Using a car jack lift the side of the car to lower the wheel to gain access to wheel well shroud.

http://www.focusfanatics.com/howtos/..._2047small.jpg

Step 5

Loosen and pull wheel well shroud back using a 8mm wrench and torx bit or allen wrench.

Step 6

Using a 10mm wrench loosen and remove the third and final bolt holding the headlamp assembly on the vehicle.

http://www.focusfanatics.com/howtos/..._2048small.jpg

Step 7

Turn on oven to 200 degrees.

http://www.focusfanatics.com/howtos/..._2052small.jpg

Step 8

While oven is warming remove the rubber trim from the headlamp assembly.

http://www.focusfanatics.com/howtos/..._2054small.jpg

Step 9

After oven as fully warmed place one headlamp on a baking/cookie sheet in the oven for about 15minutes.

http://www.focusfanatics.com/howtos/..._2053small.jpg

Step 10

Pull out the headlamp. CAREFUL ITS GOING TO BE HOT! I'd wear some sort of oven mitt or work glove to handle the headlamp.

While the head lamp is still hot using a thin flathead work around the edge of the headlamp seal to break the seal.

**NOTE**

You may have to repeat steps 9 & 10 several times over in order to fully break the seal.

Step 11

Once the clear plastic cover is removed from the black plastic housing you will have to next remove the chrome trim that is going to be painted from the clear plastic housing. TO do use remove the 2 bolts with either a torx bits or allen drive to do so.

Step 12

Mask off the area not to be painted. I'd suggest masking of at least the turn signal reflector to keep the fuzz from giving you grief. Using a razor blade to cut the outside edge of the reflector seemed to work well for me.

http://www.focusfanatics.com/howtos/..._2059small.jpg

Step 13

This step is important. Rough up all the surfaces to be painted with the scouring pad so the paint will stick to the plastic. Not doing so will result in poor adhesion of the paint.

I personally forgot this step so I didn't get as good as results as I should have.

Step 14

Pop the next headlight in the oven

Step 15

Paint. Make sure to paint in several thin layers as to one thick one. The will help avoid runs and still provide good coverage and overall consistency.

http://www.focusfanatics.com/howtos/..._2058small.jpg

Step 16

Have a beer.
Repeat steps 9 thru 15 for your second headlight.

Allow the paint to dry at least an hour before handling.

Step 17 remove the tape from the now black trim. And reinstall the painted trim into the clear housing. Don't forget the 2 screws that holds on to the clear plastic.

http://www.focusfanatics.com/howtos/..._2062small.jpg

Step 18

Using the silicone sealant run a good thick bead around the black housing where the clear plastic seats into the black housing.

http://www.focusfanatics.com/howtos/..._2069small.jpg

Step 19

Using some tape, tape the two parts together tightly and let it sit at least 8 hours.

Step 20

Remove tape and marvel at you new hotness of headlights.

http://www.focusfanatics.com/howtos/..._2065small.jpg

Step 21 Perform steps 1-6 in reverse order.

DONE!!! Now you have a unique 2005 Focus that all your friends will drool over.

http://www.focusfanatics.com/howtos/..._2206small.jpg



[:)][:)][:)][:)][:)][:)]Please Note[:)][:)][:)][:)][:)][:)]

This how-to is nothing but merely a guide on the best methods to go about the project. I do not take any responsibility of any ill-effects that occur to you vehicle from this mod or any legal issues they may arise do to the modification of your cars headlight system. PERFORM AT YOUR OWN RISK!

-Matt

SJB 09-20-2005 10:01 PM

sweet write up but i would feel weird putting my headlight in an oven

Zach16789 09-20-2005 10:02 PM

Very nice how to, and amazing looking lights, have to say this is the best headlight work i have seen, good job.

Kamui 09-20-2005 10:13 PM

Very nicely done and great write up (y)

fspeed 09-20-2005 10:15 PM

Maybe this will go to the "How-to". Great write up. The oven thing is weird, but hey, it works.

cpyder 09-20-2005 10:17 PM

Congrats..... are they eatable after baking... [:I]

[thumb] Very nice job.

2005sangriaZX3 09-20-2005 10:24 PM

very cool and looks awesome![thumb] I would be afraid that I would screw something up though.

Onyx flash 09-20-2005 10:29 PM

OMG your a friggin genious that would look so awesome on my black ride man.
great write up.

what brand paint did you use, and i have a gas oven :would this work in this project?

JohnMichael 09-20-2005 10:37 PM

Wowsers, looks totally great! If I had an '05, I would be doing this pronto...definitely should make the How-To Archive! [:D]

Onyx flash 09-20-2005 10:39 PM

^^^^^ditto(archive)


All times are GMT -5. The time now is 10:51 PM.