Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   Archive (http://www.focusfanatics.com/forum/forumdisplay.php?f=103)
-   -   BRAND NEW Ported Zetec Cylinder Head +1mm Valve Springs Ti Retainers CHEAP (http://www.focusfanatics.com/forum/showthread.php?t=308090)

K Dog 01-31-2013 05:24 PM

BRAND NEW Ported Zetec Cylinder Head +1mm Valve Springs Ti Retainers CHEAP
 
Here we have a BRAND NEW never used ported cylinder head for 00-04 Focus with Zetec. This was, as far as I know, a "one of one" custom unit done by legendary Wilson Manifolds in 2001. If you dont know who Wilson is, you might want to check them out, they are synonymous with high end, mainly custom, race induction side stuff. http://www.wilsonmanifolds.com/



Very nice port work. Not as nice as, say, a Massive head. But nice, none the less. Not a "hog it out" hack job by some amateur or moron. Some nice attention paid to the essential chamber area.
  • Crower +1mm stainless valves
  • Crower Valve springs
  • Crower Titanium retainers

The top side is hand clearanced for the very large Crower custom grind cams that had came with it, so just about anything will fit.

Never used, some assembly lube may be here and there from the old cam install.

This was milled approx .080" for BIG compression. Essential for a high HP Zetec build. If turbo is more your thing, Cometic makes thicker head gaskets in just about any thickness, so you can obtain whatever your desired CR would be. The Zetec has a very thick deck so it still has plenty of strength. If you are going for high compression, I will include a Massive prototype oversize / auxiliary timing idler kit so you can obtain proper belt tension with this head.

Only $800!!! The valve train alone would cost one near $600!!!

For an additional $250, I will include a like new set of Crower Stage 2 cams (approx 500 miles) AND correct 16 buckets, along with lashing service so it's ready to go.

Or for $350, I will include the new in box Crower custom ground stage 5 NA cams that came with the motor, 16 buckets and lash service.

Actual cost shipping.

Item is located in Spring Grove, IL.

NO DIBS. First to pay gets it.

Paypal to: orders@massivespeedsystem.com

http://zeebone.com/gallery/d/97812-1...69+_Small_.JPG
http://zeebone.com/gallery/d/97814-1...84+_Small_.JPG
http://zeebone.com/gallery/d/97816-1...89+_Small_.JPG
http://zeebone.com/gallery/d/97818-1...91+_Small_.JPG
http://zeebone.com/gallery/d/97820-1...99+_Small_.JPG
http://zeebone.com/gallery/d/97822-1...01+_Small_.JPG

ZXthrizzle05 01-31-2013 08:04 PM

Damn. When I finally want one its either tomuch $ or to high of compression

Mile30 01-31-2013 09:47 PM

This piece could change the direction on any good build... before you know it; an all-motor, high-RPM monster. I'd get it but no one wants my beater, GLWS!!!

Squareleft 01-31-2013 10:36 PM

with those stage 5's you would need a built bottom end correct?

sleepyboy 01-31-2013 10:53 PM

Oh dear baby Jesus! [pray]

d20foci 01-31-2013 11:15 PM

Come on tax refund!!!

sleepyboy 01-31-2013 11:22 PM

Sadly I have to use mine on a clutch for my SVT [V] or I would so jump on this. I think this is even worth a possible divorce for getting this [hihi]

bringler26 02-01-2013 12:23 AM

Damn I wish I had money!!

focusmaniaczx3 02-01-2013 06:32 AM

pm'd

ZXthrizzle05 02-01-2013 07:42 AM

Id poickit up if it weren't milld


All times are GMT -5. The time now is 08:03 PM.


http://www.focusfanatics.com/aboutus/copyright.asp