Ford Focus Forum, Ford Focus ST Forum

Ford Focus Forum, Ford Focus ST Forum (http://www.focusfanatics.com/forum/index.php)
-   Auto Washing, Detailing & Paint Protection (http://www.focusfanatics.com/forum/forumdisplay.php?f=52)
-   -   Clearing Hazy Head Lamps, the DIY way. (http://www.focusfanatics.com/forum/showthread.php?t=306176)

gsxrboy 01-09-2013 09:34 AM

Clearing Hazy Head Lamps, the DIY way.
 
Original Post
http://www.detailedimage.com/Ask-a-P...s-on-a-budget/

If you drive an aging car with plastic head-lamp housing, then you’re likely to experience the dangers and unsightfulness of hazy head-lights. Faded, hazy, non-clear housings cause light to refract prior to exiting the plastic rather than shining true. Not only does this result in a car looking older and losing resale value; this can also be dangerous for the operator and all others on the road as the driver struggles to make out objects through the dim light output. Changing the bulbs out for newer “true white” ones, converting to an aftermarket HID set-up, or using your brights are only temporary solutions that don’t address the true problem. Many owners are reluctant to fix the issue because of the cost of power-tools usually needed for favorable results. While using a machine like the Porter Cable 7424XP can provide much better results and take much less time to do so, many people are looking for a cheaper solution.
http://farm5.static.flickr.com/4040/...d2b5be7e_o.jpg
The vehicle being used for this educational write-up had horribly hazed-over head-lamp housings that provided very little light at night.


To begin, the headlights (and car overall) needed to be cleaned to provide a good working surface that allowed for a true inspection of the plastic housing. If you’re not worried about swirls and slight paint defects, you can take your car to a local car wash. For those looking to keep their paint looking its best, the standard two-bucket method is preferred. No-rinse washing using products like Optimum No Rinse can be a great solution for those without access to a hose.

With a clean surface, we can see just how bad things look. This will also show us how well our results may truly come out.
http://farm5.static.flickr.com/4015/...6c45dde6_o.jpg

http://farm5.static.flickr.com/4028/...ee2640bc_o.jpg
Protect the painted edges of the body and body molding pieces around your head-lamp housings using painter’s tape.
http://farm5.static.flickr.com/4030/...a08d5ae8_o.jpg
http://farm5.static.flickr.com/4055/...8453c693_o.jpg

Because we were going to be doing the work by hand, we needed to use a heavy-cut compound. In this case, Meguiar’s M105 Ultra-Cut Compound was paired with a normal foam applicator pad.
http://farm4.static.flickr.com/3337/...075933e3_o.jpg

Spread a generous amount of the compound on the pad and work small sections at a time.
http://farm4.static.flickr.com/3360/...36446bc6_o.jpg

Working small sections at a time and adding more polish as needed, use the product in a circular “polishing” motion. Here we used painter’s tape to mask off a small area for comparison purposes.
http://farm5.static.flickr.com/4050/...1d65491c_o.jpg

http://farm5.static.flickr.com/4015/...d5faf17e_o.jpg
Gently wipe of the polish residue with a microfiber towel and inspect the finish. Though this took over 20 minutes, the results say it all:
http://farm5.static.flickr.com/4038/...32dc9a08_o.jpg

http://farm5.static.flickr.com/4045/...7bb8bdbc_o.jpg
Ten-minutes after inspecting the first section, the final results for head-lamp housing number one look stunning. Though this one housing assembly took over 30 minutes to polish by hand, the cost savings for someone without a machine may definitely be worth it.
http://farm4.static.flickr.com/3308/...67f5f64c_o.jpg
http://farm4.static.flickr.com/3339/...c58c7243_o.jpg

Hand polishing is slow going, tiring, and won’t yield as good results as using a machine, but you’ll only spend a fraction of the money. If you have any questions or tips to share, please do so in the comments section below.

1sloho 01-09-2013 09:58 AM

also, suggest putting some kind of protectant over the headlights or, they will just haze back over. something like lamin-x or what i did, use 50/50 mix of spar urethane and mineral spirits and put several coats over the housing.

sbc17 01-09-2013 10:37 AM

That is a great write up! I will have to do this to my car. They aren't terrible but I am sure it is easier to do when there is less damage.

My only question is, will doing this remove the "tint" from the SVT headlights? I dunno if that is a coating on the lens or if it is part of the plastic.

-sbc

elsolo 01-10-2013 07:39 PM

If you start with a more aggressive abrasive, it goes a whole lot faster.
I wet sand starting with 1000 grit, then 1500, then 2000.....then a liquid or paste as shown in the pics above.

cdbertrand 01-14-2013 07:03 AM

Definetly trying this soon. What exact product am I to coat the lens with after this step?

nickstewartroc 01-28-2013 09:05 PM

If you don't have the cutting compound, you can try toothpaste! Just did it to my gf's Pt Cruiser, and damn, they look brand new! Just another input is all [cheers]

-Nick

cdbertrand 01-29-2013 06:58 AM

What kind exactly?

nickstewartroc 01-29-2013 07:00 AM

I just used some old tube I had, I think it was Crest or something

cdbertrand 01-29-2013 07:06 AM

Hmmm interesting. might have to hit up dollar general and get a tube haha.

tukaniSVT 01-29-2013 07:48 AM

Ive done it that way as well. And It works wonders. Nice job.

Ray


All times are GMT -5. The time now is 07:22 PM.


http://www.focusfanatics.com/aboutus/copyright.asp