Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   Auto Washing, Detailing & Paint Protection (http://www.focusfanatics.com/forum/forumdisplay.php?f=52)
-   -   Bonnet chip repairs. (http://www.focusfanatics.com/forum/showthread.php?t=298731)

sicskate 09-29-2012 06:43 PM

Bonnet chip repairs.
 
Work was a tad slow last week, so i thought i'd take advantage and make this quide.

the bonnet in question,
2012 Ford S-MAX
Panther black.

http://i34.photobucket.com/albums/d1...47ADF0FE60.jpg

the chips were 3-4mm in diameter each.

Start by scotching the chips, making sure the centre of the chips are etched.
This is to help the new paint hold.
http://i34.photobucket.com/albums/d1...47DE703BF7.jpg

next its time for paint 1:1:1 base/lacquer/hardner
http://i34.photobucket.com/albums/d1...47EF5D64B1.jpg
mix paint well.

Clean the area with silicon inferno (no pics).
this is to remove dust from the scotching from the chip.

Add the paint with a thin brush, i used a 1mm fine tipped brush.
When adding the paint, you don't want to put a massive blob in, but you ideally need the new paint to overlap the outside of the chip by 0.5mm.
http://i34.photobucket.com/albums/d1...4807713555.jpg

Time to get some heat on it. 15mins at160 degrees C should do, but a few hours in the sun will do the job.
http://i34.photobucket.com/albums/d1...4810EBE8AA.jpg

After a bake,
http://i34.photobucket.com/albums/d1...48270F91EF.jpg

Due to the size of these chips, i decided to let this area cool and re-bake them again for good luck.

Once cooled, I'm using a paint shaving block to trim the new paint down to a closer to level point.
http://i34.photobucket.com/albums/d1...48499BD1AB.jpg
http://i34.photobucket.com/albums/d1...484F81516C.jpg
http://i34.photobucket.com/albums/d1...4854F64A98.jpg

The dark shiny bits are the LOW parts.
So its time to scotch it up and put some fresh paint back in.
http://i34.photobucket.com/albums/d1...485C48D52E.jpg
http://i34.photobucket.com/albums/d1...486345F1AE.jpg

So after a re-bake and cool down, i've shaved it down again abd all was good.

A quick flat with some wet'n'dry 2000 paper and a rubber block to keep it flat.
http://i34.photobucket.com/albums/d1...486AB70AB4.jpg

Other chipped areas i was working on.
http://i34.photobucket.com/albums/d1...4870F0A53C.jpg

Time for some polish (med cutting compound)
http://i34.photobucket.com/albums/d1...4876E43544.jpg
with a lambs wool head.
http://i34.photobucket.com/albums/d1...481FCF35FF.jpg

Area polished.
http://i34.photobucket.com/albums/d1...487CD0AA36.jpg

Time for a very soft swirl / hologram remover with a very soft foam head on a slow steady speed.
http://i34.photobucket.com/albums/d1...4887FEBF9C.jpg
http://i34.photobucket.com/albums/d1...488E780B4A.jpg
http://i34.photobucket.com/albums/d1...4894ED320A.jpg

Wiped down with a microfibre cloth
http://i34.photobucket.com/albums/d1...48A88BBE14.jpg

Now time for some wax. apparently up & down reduces shadows.
http://i34.photobucket.com/albums/d1...48AE436FDF.jpg

Left to cure for 5 mins and wiped off.

http://i34.photobucket.com/albums/d1...48BB113F88.jpg
http://i34.photobucket.com/albums/d1...48D1C6587A.jpg

Finished article :dance:
http://i34.photobucket.com/albums/d1...48D8E834B0.jpg

And off it goes along the production line.

I'd like to add, that the bonnet was not detailed in anyway at this point.

lyonsroar 09-29-2012 07:29 PM

This is not really something a DIY'r would feel comfortable handling I would think.
GREAT results though.

The home repairer might be more comfortable with this:
http://www.drcolorchip.com/

dbenney 09-29-2012 09:04 PM

Quote:

Originally Posted by lyonsroar (Post 4379315)
This is not really something a DIY'r would feel comfortable handling I would think.
GREAT results though.

I guess it all depends on what you are comfortable with. I have done some painting and I would feel comfortable with doing that. Its basic touch up.

to the OP... great write up!

Burns098356GX 10-02-2012 11:41 AM

Petty impressive, not something I've got the talent for though. I've got some doctorcolourchip coming this week, hope it works. My focus is tuxedo black which appears to be very similar to the European panther black.

Sent from my Nexus 7 using FF Mobile

gsxrboy 10-02-2012 01:38 PM

Awesome article, thank you for writing this up. I am definitely not doing this myself, but at least I know what it takes to complete and I can hunt around for prices in my neighborhood.

Burns098356GX 10-03-2012 09:17 PM

Is this the type of work a body shop will do? I filled my own chips on my last car, which was mostly junk. I'd like to get a couple chips on the hood of my new focus taken care of. I always thought the only way to really fix that type of damage was to completely repaint it.

Sent from my Nexus 7 using FF Mobile


All times are GMT -5. The time now is 01:07 AM.


http://www.focusfanatics.com/aboutus/copyright.asp