Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   General Forced Induction (http://www.focusfanatics.com/forum/forumdisplay.php?f=44)
-   -   Lets see what this heat maker can do-JRSC build (http://www.focusfanatics.com/forum/showthread.php?t=265034)

disciplerocks 08-06-2011 08:38 AM

Lets see what this heat maker can do-JRSC build
 
So I am planning on gathering parts and start building this winter. Been working on a couple things so far.

Current setup:
M45
6.5" crank pulley
2.6" blower pulley
ZX2 cams
COP
SVT airbox
OBX header/catback
FC cam gears
E85
http://i19.photobucket.com/albums/b1.../IMAG01261.jpg


List of plans:
Head milled and mildly ported
Larger valves
Replace the M45 with a mildly ported M62
Smaller sc pulley (offset is different for the GM M62, undecided on size)
Aluminum flywheel and clutch (undecided on clutch)
SVT rods (undecided on pistons)
W/M or N2O (DD, but will rarely see high boost)
Tube arms (built by me)
Traction bars (built by me)


Now this is what I have so far

Brand new aluminum flywheel
http://i19.photobucket.com/albums/b1...d/IMAG0152.jpg

SVT rods and pistons with new rings and bearings installed
http://i19.photobucket.com/albums/b1...d/IMAG0151.jpg

And an M62 off a 95 Riviera
http://i19.photobucket.com/albums/b1...d/IMAG0153.jpg

The blower is getting stripped down and cut up to fit the JRSC throttle body plate. Will be replacing the bearings, coupling, and seals.

Posted via FF Mobile

disciplerocks 08-06-2011 08:39 AM

This is being copied from somewhere else so bear with me.
Posted via FF Mobile

disciplerocks 08-06-2011 08:43 AM

This is what is done so far.
http://i19.photobucket.com/albums/b1...d/IMAG0154.jpg
http://i19.photobucket.com/albums/b1...d/IMAG0157.jpg
http://i19.photobucket.com/albums/b1...d/IMAG0162.jpg
http://i19.photobucket.com/albums/b1...d/IMAG0159.jpg
http://i19.photobucket.com/albums/b1...d/IMAG0158.jpg
Posted via FF Mobile

disciplerocks 08-06-2011 08:48 AM

Down to the rotor bearings. Can't cut anymore off.
http://i19.photobucket.com/albums/b1...d/IMAG0170.jpg

I can save about .5" by keeping the GM pulley because of the offset.
http://i19.photobucket.com/albums/b1...d/IMAG0171.jpg

The case is still 1.75" longer than my M45. I need things to match up for the bypass valve you can see here.
http://i19.photobucket.com/albums/b1.../SSPX41331.jpg


I should be able to move the assembly toward the belt the other .25" or so. There is plenty of mounting surface on the manifold.
Posted via FF Mobile

disciplerocks 08-06-2011 08:52 AM

http://i19.photobucket.com/albums/b1...d/IMAG0174.jpg
http://i19.photobucket.com/albums/b1...d/IMAG0179.jpg
Posted via FF Mobile

disciplerocks 08-06-2011 09:41 AM

Also going to be swapping in 4.06 gears, and hopefully a custom L/S diff.

Been eyeing these too
https://m.ebay.com/Member/F/ViewItem...40x278&emvcc=0
Posted via FF Mobile

Ryan03svt 08-06-2011 11:22 AM

Sweet build. looking forward to seeing this done

iceberg65 08-06-2011 12:39 PM

I hope by custom L/S diff you don't mean that phantom grip.

disciplerocks 08-06-2011 01:53 PM

Hell no. That wouldn't be custom. I am planning on replacing the whole diff.

mlbbaseball 08-06-2011 02:26 PM

looks like you got your work cut out for you!


All times are GMT -5. The time now is 09:34 PM.


http://www.focusfanatics.com/aboutus/copyright.asp