Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   General Forced Induction (http://www.focusfanatics.com/forum/forumdisplay.php?f=44)
-   -   Turbo Zetec Build. For Iroc34 (http://www.focusfanatics.com/forum/showthread.php?t=251626)

iroc34 02-24-2011 10:48 PM

Turbo Zetec Build. For Iroc34
 
Well, I was warned. I kind a new it would happen. Time for some more boost.
Here is what I have gotten into.

Low Mileage Zetec Block. Bored/Honed with deck plate .007 over.
Stock Crank , oil holes chamfered, polished journals
Eagle connecting rods. JE 9.0 -1 pistons.
Comp cams stage II`s. All new Ford Racing valves and spring kit.
Cylinder head ported . Ford Racing Intake Manifold ported and Modified to Ford Racing Specs. FRIM port matched to the head.
75mm Roush Racing throttle Body. Kenne Bell BAP . New SVT fuel Pump. And the 60lbs injectors.
ARP main and head studs. AEM cam gears.
Fidanza Flywheel, Competition Clutch stage 4 clutch.
Tial 50mm BOV and Tial 44mm WG.
New 2.5" hot side and 3" cold side to tb aluminum pipe.
Low mileage MTX with Torsen installed.

And some pics. Block .007 over
http://www.focusfanatics.com/forum/p...pictureid=5495
Eagle Rods
http://www.focusfanatics.com/forum/p...pictureid=5494
Getting assembled
http://www.focusfanatics.com/forum/p...pictureid=5500
ARP mains and Eagle rods installed
http://www.focusfanatics.com/forum/p...pictureid=5504

Will add more pics. Just getting started.

focusboy5 02-24-2011 11:08 PM

You going to get a bigger turbo?

iroc34 02-24-2011 11:29 PM

Absolutely. Gonna break in this engine with the set up I have and then shoot for 400 hp max. Run 300 -325 on the street.

Some more Pics. Comp Stage II`s
http://www.focusfanatics.com/forum/p...pictureid=5497
Ford Racing Intake
http://www.focusfanatics.com/forum/p...pictureid=5566
Head Being Ported
http://www.focusfanatics.com/forum/p...pictureid=5496

focusboy5 02-24-2011 11:31 PM

What turbo are you looking at?

iroc34 02-24-2011 11:35 PM

Gonna get with Tom . And see where we want to be.

iroc34 02-25-2011 08:23 AM

Should I go with the AEM Gears that I have . Or the OBX`s that came with the engine. OBX used to make some cheap stuff, but I have to say these cam gears look like nice quality. But there also blue. And the Tials are purple. And I do have the Massive Cam Gear bolts and the washers are purple. I thought they would look better with the AEM`s.
OBX Gears
http://www.focusfanatics.com/forum/p...pictureid=5492
AEM Cam Gears
http://www.focusfanatics.com/forum/p...pictureid=5578
Tial Waste gate
http://www.focusfanatics.com/forum/p...pictureid=5576
Tial BOV
http://www.focusfanatics.com/forum/p...pictureid=5575

Mother Focus 02-25-2011 08:37 AM

Edit: just noticed the AEM's are only 3 bolts, 5 may be more secure.

iroc34 02-25-2011 08:47 AM

Quote:

Originally Posted by Mother Focus (Post 3571577)
Edit: just noticed the AEM's are only 3 bolts, 5 may be more secure.

Good Point. But I havnt heard of any one having trouble with the AEM`s , Have you?

1turbofocus 02-25-2011 08:52 AM

I havent , I have had about everything there is in my shop for cam gears and never seen any issues with any of them

Looking good

Tom

iroc34 02-25-2011 09:01 AM

Quote:

Originally Posted by 1turbofocus (Post 3571604)
I havent , I have had about everything there is in my shop for cam gears and never seen any issues with any of them

Looking good

Tom

OK cool, I am leaning towards the AEM`s. Just because of color coordination.
Blue and purple. IDK ?


All times are GMT -5. The time now is 09:40 PM.


http://www.focusfanatics.com/aboutus/copyright.asp