Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum

Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum (http://www.focusfanatics.com/forum/index.php)
-   MK1 Interior Mods & Upgrades (http://www.focusfanatics.com/forum/forumdisplay.php?f=46)
-   -   HOW TO: Interior swap with power window and locks (over 100 pics) (http://www.focusfanatics.com/forum/showthread.php?t=219941)

focuzed1 01-01-2010 12:12 AM

HOW TO: Interior swap with power window and locks (over 100 pics)
 
Ok for those that want it i hope this helps.. just so you know this is with after market wiring.. and only the master window switch in a custom place.

In this how to i replaced a zx3 no power option with svt eap power everything.
seat heaters with factory switches.
factory power window with single switch
factory door locks hooked to aftermarket alarm

hope you like it...

Here we go.. first like always.. turn on some music..
http://i44.photobucket.com/albums/f3...akeswap008.jpg

then we start tear down..
http://www.focusfanatics.com/howtos/...iorswap008.jpg

disconnect battery..
http://www.focusfanatics.com/howtos/...iorswap056.jpg

then pull of this panel behind the handle.. it has a cover and one screw then it just pulls off.
http://www.focusfanatics.com/howtos/...iorswap015.jpg

then take off all the screw to the panel..
http://www.focusfanatics.com/howtos/...iorswap014.jpg
http://www.focusfanatics.com/howtos/...iorswap016.jpg
http://www.focusfanatics.com/howtos/...iorswap017.jpg

take out the cover over the door handle grip and the 2 screws behind it
http://www.focusfanatics.com/howtos/...iorswap019.jpg
http://www.focusfanatics.com/howtos/...iorswap020.jpg

then pull off this cover pull back then out..
http://www.focusfanatics.com/howtos/...iorswap021.jpg

then pull the panel off
http://www.focusfanatics.com/howtos/...iorswap022.jpg

then the foam..
http://www.focusfanatics.com/howtos/...iorswap023.jpg

then your speaker .. 4 bolts and a plug..
http://www.focusfanatics.com/howtos/...iorswap025.jpg

then the door latch handle. pull the front of the handle out first
http://www.focusfanatics.com/howtos/...iorswap027.jpg

then pull off the foam blanket piece.
http://www.focusfanatics.com/howtos/...iorswap029.jpg

now the 3 bolts to the latch
http://www.focusfanatics.com/howtos/...iorswap028.jpg

then this screw
http://www.focusfanatics.com/howtos/...iorswap034.jpg

there is 2 on this handle inside the door one you can see plainly and the other you can see through this hole
http://www.focusfanatics.com/howtos/...iorswap031.jpg

this part of the handle will come off first
http://www.focusfanatics.com/howtos/...iorswap035.jpg

then the rest of the handle
http://www.focusfanatics.com/howtos/...iorswap036.jpg

then wiggle the latch assy out
http://www.focusfanatics.com/howtos/...iorswap037.jpg

then lower the window down about half way
http://www.focusfanatics.com/howtos/...iorswap048.jpg

and loosen the 2 bolts here..
http://www.focusfanatics.com/howtos/...iorswap046.jpg
http://www.focusfanatics.com/howtos/...iorswap047.jpg

then roll up your window and tape it up..
http://www.focusfanatics.com/howtos/...iorswap038.jpg

now i had an aftermarket power window set up in this car before so this is where it will differ a little bit ..
disconnect the window track assy.
http://www.focusfanatics.com/howtos/...iorswap039.jpg
http://www.focusfanatics.com/howtos/...iorswap040.jpg
http://www.focusfanatics.com/howtos/...iorswap041.jpg
http://www.focusfanatics.com/howtos/...iorswap042.jpg
http://www.focusfanatics.com/howtos/...iorswap043.jpg
http://www.focusfanatics.com/howtos/...iorswap045.jpg

wiggle it out
http://www.focusfanatics.com/howtos/...iorswap049.jpg

this is what you should have now
http://www.focusfanatics.com/howtos/...iorswap050.jpg

now take your power assy..
http://www.focusfanatics.com/howtos/...iorswap051.jpg

and reverse your steps..

wiggle it in
http://www.focusfanatics.com/howtos/...iorswap052.jpg

then bolt it in
http://www.focusfanatics.com/howtos/...iorswap053.jpg

now we are going to change out the locks on the old door handle to our new handle assy
http://www.focusfanatics.com/howtos/...iorswap061.jpg

2 screws here
http://www.focusfanatics.com/howtos/...iorswap062.jpg

then push this tab out
http://www.focusfanatics.com/howtos/...iorswap066.jpg

while trying to get out the piece you just unscrewed you could probably twist this out
http://www.focusfanatics.com/howtos/...iorswap068.jpg

now wiggle this out (silver bar)
http://www.focusfanatics.com/howtos/...iorswap069.jpg

and switch this piece (handle/lock assy) (whole assy) and reverse your steps..
http://www.focusfanatics.com/howtos/...iorswap069.jpg

reinstall your handle and latch assy reversing the steps of removal
now do the same for the other side

now we are gonna work on the interior...
I already had installed the recaros but they were not hooked up

so first the seats
unplug them
http://www.focusfanatics.com/howtos/...iorswap071.jpg

pull off the covers and then unbolt them
http://www.focusfanatics.com/howtos/...iorswap070.jpg
http://www.focusfanatics.com/howtos/...iorswap074.jpg
http://www.focusfanatics.com/howtos/...iorswap075.jpg

now the under seat entertainment..lol
http://www.focusfanatics.com/howtos/...iorswap077.jpg

then the back lower seats.
http://www.focusfanatics.com/howtos/...iorswap078.jpg

this is what you should be at now.
http://www.focusfanatics.com/howtos/...iorswap079.jpg

then the back rests i forgot these pics sorry.. easy though.. just 5 bolts and the 3 seatbelts

the the center console
first the forward cover
http://www.focusfanatics.com/howtos/...iorswap086.jpg
http://www.focusfanatics.com/howtos/...iorswap087.jpg

then the cover for the bolts and then the bolts for the arm rest
http://www.focusfanatics.com/howtos/...iorswap080.jpg

then the two bolts under the cup holders and one in the back cup holder
http://www.focusfanatics.com/howtos/...iorswap081.jpg

then pull out your center console (you will not have these wires mine is from my power window kit)
http://www.focusfanatics.com/howtos/...iorswap082.jpg

then the arm rest bracket
http://www.focusfanatics.com/howtos/...iorswap088.jpg

then the front seat belt lower brackets.
http://www.focusfanatics.com/howtos/...iorswap085.jpg

then the rear vet tubes
http://www.focusfanatics.com/howtos/...iorswap089.jpg

this is where you should be now...
http://www.focusfanatics.com/howtos/...iorswap084.jpg

then the interior trip peices which are mostly clipped in.
http://www.focusfanatics.com/howtos/...iorswap118.jpg

now your carpet.. its held in by multiple clips down the side...
http://www.focusfanatics.com/howtos/...iorswap090.jpg

and pull it out..
http://www.focusfanatics.com/howtos/...iorswap092.jpg

now here is where things might really differ from your car.. i wired it like this to an wire with accy power..
yellow and green wired to yellow and orange
all balck wires together.
green and red to driver seat
green and blue to passenger seat
http://www.focusfanatics.com/howtos/...iorswap094.jpg
here is the switch diagram i used (thanks yzo4)
Quote:

Originally Posted by YZ04 (Post 3082345)

this one for the seat plugs

Quote:

originally quoted on focal jet by mjmallon

For the Driver seat:

svt pin 1: driver side-airbag signal: wire to driver seat harness pin 9
svt pin 2: driver side-airbag return: wire to driver seat harness pin 10
svt pin 3: not used
svt pin 4: not used
svt pin 5: seat heaters switched power pass-through: jumper with svt pin 11
svt pin 6: heated seats switched power: wire to driver seat harness pin 5 (green and red wire)
svt pin 7: seatbelt buckle sensor signal: wire to driver seat harness pin 3
svt pin 8: seatbelt buckle sensor return: wire to driver seat harness pin 4
svt pin 9: powered seat-height power: wire to constant power
svt pin 10: powered seat-height ground: wire to ground
svt pin 11: seat heaters switched power pass-through: jumper with svt pin 5
svt pin 12: seat heaters ground: wire to passenger seat harness pin 8
svt pin 13: seat track position sensor signal: wire to driver seat harness pin 1
svt pin 14: seat track position sensor return: wire to driver seat harness pin 2

For the Passenger seat:

svt pin 1: passenger side-airbag signal: wire to passenger seat harness pin 9
svt pin 2: passenger side-airbag return: wire to passenger seat harness pin 10
svt pin 3: seatbelt pretensioner switched power: wire to passenger
seat harness pin 5
svt pin 4: seatbelt pretensioner signal return: wire to passenger seat
harness pin 6
svt pin 5: heated seats switched power: wire to passenger seat harness pin 1 (green and blue wire)
svt pin 6: seat heaters switched power pass-through: jumper with svt pin 11
svt pin 7: seatbelt buckle sensor signal: wire to passenger seat harness pin 3
svt pin 8: seatbelt buckle sensor return: wire to passenger seat harness pin 4
svt pin 9: not used
svt pin 10: not used
svt pin 11: seat heaters switched power pass-through: jumper with svt pin 6 (red and orange wire to accy power)
svt pin 12: heated seats ground: wire to passenger seat harness pin 8(to black wires on switches)
svt pin 13: not used
svt pin 14: not used
(ill get you colors for these soon)

ok a bit more now.. after you ahve wired up your seat heaters lset go ahead and do the window switch... i decided to use the master switch and put it in my center console but you can do the same using the switches if you want to run all the wires to both sides of the car..

heres is the plug for the master switch
and how to wire them up..
green is your accy power
black is your ground
the yellow and white on the side of the ground is for the passenger side (just hook them up temporarly so you can figure which is up and which is down)
the yellow and white on the side of the plug with the green wire goes to driver side.
http://www.focusfanatics.com/howtos/...iorswap099.jpg
http://www.focusfanatics.com/howtos/...iorswap100.jpg
okfocusinteriorswap100.jpg[/IMG]

run your wires to the doors (which mine was already done) and clean it up.
http://www.focusfanatics.com/howtos/...iorswap101.jpg

then remove the door wire harness by turning this plug and pull it out
http://www.focusfanatics.com/howtos/...iorswap054.jpg

then put the new harness back in and run it through the door

now time for power to your window motor..this is what i did with the plugs for the power window motor this is where you will test the switch to see which is up or down.. if you push the switch and its the wrong way then just switch the 2 wires areound and sinch it up.
http://www.focusfanatics.com/howtos/...iorswap102.jpg

now its time for the locks..the factory set up you have to switch the gem unit but i had my aftermarket alarm set up in the doors so i just hooked those up since i wasnt using the switches anyways.


same setup here.. splice into the wires and test it.. if its wrong then switch it..
on the driver side there is 4 wires.. its the bigger 2 wires of the 4. i cant remember the color.
http://www.focusfanatics.com/howtos/...iorswap103.jpg

since i wasnt using the other switches or the power mirrors i just sinched up teh wires just in case later i changed my mind.
http://www.focusfanatics.com/howtos/...iorswap104.jpg

now we start reassembly
the foam and blanket and door latch handle
http://www.focusfanatics.com/howtos/...iorswap111.jpg

speaker
http://www.focusfanatics.com/howtos/...iorswap112.jpg

door panel, mirror wire cover and handle cover
http://www.focusfanatics.com/howtos/...iorswap113.jpg

on now on to carpet.. just position and clip in make sure you pull through the plugs and your entertianment wires
http://www.focusfanatics.com/howtos/...iorswap116.jpg
http://www.focusfanatics.com/howtos/...iorswap114.jpg

now the seat belt bracket
http://www.focusfanatics.com/howtos/...iorswap115.jpg

now for the underseat entertainment
http://www.focusfanatics.com/howtos/...iorswap117.jpg

rear panels
http://www.focusfanatics.com/howtos/...iorswap120.jpg

trim peices
http://www.focusfanatics.com/howtos/...iorswap118.jpg

now get a buddy you trust and install front seats.. [hihi]
http://www.focusfanatics.com/howtos/...iorswap119.jpg

now back seats
http://www.focusfanatics.com/howtos/...iorswap121.jpg
http://www.focusfanatics.com/howtos/...iorswap123.jpg

now place your rear spare tire cover in..
http://www.focusfanatics.com/howtos/...iorswap122.jpg

and the rest of your under seat entertainment..
http://www.focusfanatics.com/howtos/...iorswap124.jpg

guess what... YOUR DONE... NOW STAND BACK AND ENJOY!!!!!

kenzx3 01-01-2010 01:23 AM

Plus 1 Rep, very informative [thumb]

norcalfocus01 01-01-2010 01:25 AM

Im going to add this to the sticky at the top of the page.

Broncoboy80 01-01-2010 05:30 AM

Saveeeet!

YZ04 01-01-2010 03:45 PM

Niiice! Wish someone did a complete write-up like this before I did my own power window and lock conversion.

focuzed1 01-01-2010 09:16 PM

me too...lol... would have made life alot easier huh...lol..

1stTimeFocus00 01-02-2010 03:50 PM

damn. wish i was that smart. I wonder if theres a how-to to put cruise control in our car.

focuzed1 01-02-2010 08:29 PM

i thought i saw one somewhere but i dont remeber where it was..

GodLovesUgly 01-02-2010 11:49 PM

nice work man. rep for sure.

stoopidsteve87 01-03-2010 01:42 AM

should've used my car as your example lol


All times are GMT -5. The time now is 01:17 AM.