Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   DURATEC Performance (2008-2011) (http://www.focusfanatics.com/forum/forumdisplay.php?f=329)
-   -   How-To: Shorten your shift throw with stock MTX shifter (http://www.focusfanatics.com/forum/showthread.php?t=209254)

FucusUnderground 08-24-2009 10:00 PM

How-To: Shorten your shift throw with stock MTX shifter
 
Let me start by saying I didn't invent this DIY mod. It's discussed a bit in the STS sticky, and the first reference made to it was by Buickboy so I want to make sure he gets his fair credit. The sticky is rather vague as far as what's involved and I couldn't find it mentioned anywhere so I decided to do a write up on it. Many of you may know of this already but since it's so easy and free it should be readily availabe for people who want a shorter throw but can't or don't want to spend money on one. I did it, and it works great. Bear in mind this is my first writeup so be gentle. Also, my phone's camera sucks so forgive the quality of the pics.

What you will need:
-Phillips Head screwdriver
-Flathead screwdriver
-Cutting tool (serrated steak knife, mini handsaw, etc) for red plastic collar
-Wirecutter (reccommended) for boot trim

What you do:

Start by moving the front passenger seat all the way back. This will give you more room to work with. Don't mind my shift knob. I'm on my 4th one. I guess Ford can't make one for me that will keep paint on.
http://www.focusfanatics.com/howtos/...cusshifter.jpg

Next, gently pry the shift boot from the console. Be careful, it's only held in there by plastic tabs so try not to break them off.
http://www.focusfanatics.com/howtos/...removeboot.jpg

Now, remove the shift knob. It just twists off but it may take some persuasion to get it started.
http://www.focusfanatics.com/howtos/...removeknob.jpg

With the knob removed, you can take off the entire shift boot assembly. Take the red plastic collar and set it aside for now.
http://www.focusfanatics.com/howtos/...movecollar.jpg

With the boot assembly out of the way you should be left with a bare shift lever with black plastic piece attached near the bottom. This the pivot ball mount and is what we're going to move. Using a Phillips Head screwdriver remove the screw you see pictured. It may help to have a few different phillips heads because this screw can be tough to get started, and it strips kind of easy. It's one of those screws that seem to want one specific driver (anyone who has worked on cars to a large extent knows what I mean).
http://www.focusfanatics.com/howtos/...pinchscrew.jpg

Ok now with that screw out it's time to reposition the pivot ball mount. You will see that the screw was pinching the two black "fingers" that circled the lever together when it was all together. Get a flathead screwdriver that JUST fits inbetween those two fingers. By **gently** prying them apart you will notice the mount get a little looser. Basically you want to pry them just enough so you can move the whole mount up the lever. After playing with it for a minute you'll find the technique that works. Move it up until you can twist the mount on the lever without prying on it. NOW, using the prying technique, LOWER the mount on the lever just until you are no longer able to move it around without prying. I know these pics aren't that great but here's where it was before you moved it:
http://www.focusfanatics.com/howtos/...r/mountlow.jpg

And here's an approximation of where it should be after you move it:
http://www.focusfanatics.com/howtos/.../mounthigh.jpg

Once you're comfortable with it's position, you can go ahead and put the screw back in an tighten it up. At this point there's two more things you're going to need to do before you can button everything back up. First, try to reinstall the shift boot assembly (lining up the notch on the boot's sleeve with the peg on the mount-it only goes on one way) and more likely that not it's not going to go on right when you try to snap the trim into place. This is because we moved the mount up so high that the boot's trim in now touching the pivot arm. Take your wire cutters, or any other heavy-duty snipping devices and trim the front of the boot's trim. You'll see where. I removed the whole front tab thing below the two mounting tabs (so they'd hold the boot on since i cut the staple off). It's more trial and error but eventually once you remove enough material it'll snap on and you're good. I didn't take a pic but if someone ABSOLUTELY needs me to I'll take it apart and post one.
Now remember the red plastic collar I had you set off to the side? If you put it back on as it is it will cover the threads on the lever preventing the knob from going back on. Again, you want to trim it down so that enough of the thread is exposed to replace the knob. I took off about an inch give or take. Again no pic but it's pretty self explanitory. Once you have that all set, twist the shift knob back on and take her for a spin.

You will find that not only are the throws noticeably shorter than they were in its previous configuration, but I also found on mine that the shifter is nice and firm, especially in neutral. I wouldn't have called it sloppy before but now I can't think of a better word for what it used to feel like. Takes about a half hour or so, costs nothing but a few moments of your time, and is a great alternative to shelling out over $100 for an aftermarket shifter. Bear in mind though, that I can't speak for the difference between this mod and a STS like Steeda's as I've never used one, but vs stock this is your best bang (into gear) for your buck.

Good Luck and happy motoring guys!

screammachine 08-24-2009 11:19 PM

thanks Buickboy and FucusUnderground im going to have to try this when i get my car out of the shop i love how its FREE

warneej 08-24-2009 11:43 PM

Hmm...mine didn't have a red plastic collar but you got the Short Throw theory down pat it seems.

FucusUnderground 08-25-2009 08:43 AM

No problem screammachine although all I did was write it up. I had seen it mentioned a few times and couldn't find a how-to so I made this for the benefit of those who want to do it but couldn't find the info. As I said above I have never used a "true" aftermarket short throw shifter so I honestly can't say how much they shorten throws but I was able to move the ball mount up pretty much a full inch on mine and the throws are shorter than they were. It doesn't make the throws rediculously short like on some cars but you should notice the difference. I can't immagine a Steeda or a B&M's throws to be much shorter than this anyway (at least not a $120 difference) but again, I don't know. Anyone who has used an aftermarket shifter feel free to weigh in on this.

honhon 08-25-2009 09:01 AM

my only concern with this idea is the part you can see in the last and 2nd to last picture, but the cable will come close to the plastic piece that holds the boot in, and i had this issue with my B&M and i had to trim the plastic alittle

FucusUnderground 08-25-2009 09:22 AM

It does come into contact with it. I had to trim mine also. And I've heard others say they have had to do the same thing with the Steeda model. This point only adds weight to the argument that it's essentially doing the same thing as one of those shifters. And ig you trim it right, you'll never be able to tell once it's back in place. Even if you reset it to the stock configuration no one would know unless they pulled up the boot.

bdnld4482 08-25-2009 10:22 AM

Quote:

Originally Posted by honhon (Post 2901622)
my only concern with this idea is the part you can see in the last and 2nd to last picture, but the cable will come close to the plastic piece that holds the boot in, and i had this issue with my B&M and i had to trim the plastic alittle

^^^^x2. it does hit the boot and will somtimes pop the boot out and even wear out the plastic boot. time to upgrade to leather boots

bosengel 08-25-2009 12:33 PM

For those that are unsure about the red collar, it was only found on 2007s that came without a reverse lockout. On older models, there will be a spring in it's place.

And for your paint peeling, I had the same problem. Scraping it all off doesn't look half bad.

http://i807.photobucket.com/albums/y...s/DSC00709.jpg

FucusUnderground 08-25-2009 01:08 PM

That's actually pretty funny you mentioned that. I just removed the paint except for the paint in the numbers and it looks pretty darn good. My warranty for those ran out finally lol so no 5th free one for me. And they wanted to charge me over $50 for a stock knob...eff that.

Also thank you for clarifying the red collar. I just assumed since mine had it that they all did.

warneej 08-25-2009 11:54 PM

lol at the Crown Royal bag boot.

And yes I had to trim my collar with the Steeda STS, its a pretty standard thing.

May want to edit the post or clarify.


All times are GMT -5. The time now is 10:31 AM.


http://www.focusfanatics.com/aboutus/copyright.asp