Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   Brakes, Suspension & Body Chassis (http://www.focusfanatics.com/forum/forumdisplay.php?f=159)
-   -   Svt rear brake pads (http://www.focusfanatics.com/forum/showthread.php?t=204230)

tukaniSVT 07-04-2009 02:28 PM

Svt rear brake pads
 
So ... Visiting my family in Dallas TX my brakes starting acting funny and squeaking and all kinds of not so good noises.

Well it turned out to be my rear brake pads were over due for a change.

So I decided, since there are lots of new owners of previously owned SVTs now, I wanted to share a "How-To" do the Rear Brakes since the SVTs have discs instead of drums. And the manuals do not have the SVTs in them ... unless you get the FORD Standard Manual ... which I found is hard to find.

I also looked in the How-To Archive and the Rear SVT ones are not here. I've done this before ... but just wanted to share.

Anyways, here you guys go.

1ST off You want to go to AutoZone and buy a Disc Brake Piston tool.
http://i232.photobucket.com/albums/e...s/Brakes15.jpg

Now ...

1) Find a good place to do this. I like finding shade when working on the car ... especially since I live in TX. Goodness.
http://i232.photobucket.com/albums/e...es/Brakes1.jpg

2) Put a brick or something equivalent to the other tires that you are not working on. Helps the roll of the car.
http://i232.photobucket.com/albums/e...es/Brakes2.jpg

3) Put your car in 1st Gear and release the E-Brake.
http://i232.photobucket.com/albums/e...es/Brakes4.jpg
http://i232.photobucket.com/albums/e...es/Brakes7.jpg

4) Good a good Hydraulic Jack (Ummm if you use the Small dinky one from Ford in your car ... please be careful) I also recommend some good Jack Stands as well. (If you are new ... )
http://i232.photobucket.com/albums/e...es/Brakes8.jpg
http://i232.photobucket.com/albums/e...s/Brakes13.jpg

5) Next Start to Take off the Lugs. I do this in a criss cross pattern that way it's evenly taken off and evenly put on.
http://i232.photobucket.com/albums/e...es/Brakes9.jpg

6) As an extra precaution I put my wheel under the car as well. ... Hey can never be overly Safe. It's just something I do. Wheels are cheaper than fixing the the whole strut and all ... But that's just me.
http://i232.photobucket.com/albums/e...s/Brakes14.jpg

7) I would also recommend some good ol' Gloves. Alrighty well lets do this now ...
http://i232.photobucket.com/albums/e...s/Brakes11.jpg
http://i232.photobucket.com/albums/e...s/Brakes12.jpg

8) Now with the wheel off you will see the brake caliper. There are bolts on the back side of the caliper. You will need a 13mm socket and a 15mm wrench to get this off. There are 2 of them. One on top and one on bottom. The 15mm is too help the bolt from just spinning and not coming off.
http://i232.photobucket.com/albums/e...akes17copy.jpg
http://i232.photobucket.com/albums/e...s/Brakes18.jpg
http://i232.photobucket.com/albums/e...s/Brakes19.jpg
http://i232.photobucket.com/albums/e...s/Brakes20.jpg
http://i232.photobucket.com/albums/e...s/Brakes21.jpg
http://i232.photobucket.com/albums/e...s/Brakes23.jpg

9) Now that you have the bolt off. You need to wiggles the Caliper off. It's on there. So wiggle with some force. The Force wasn't with me, so I just used my hands and rocked it back and forth til it came off. (Okay that was corny ... anyways).
http://i232.photobucket.com/albums/e...s/Brakes24.jpg
http://i232.photobucket.com/albums/e...s/Brakes25.jpg

10) Take off the pads. Eww some nasty ones here with not much beef. I am embarrassed to show you my other side ... (**OH FOOTNOTE**) When changing brake pads. It is best to change both sides not just one side.
http://i232.photobucket.com/albums/e...s/Brakes26.jpg
http://i232.photobucket.com/albums/e...s/Brakes27.jpg

New ones are shiny. Too bad Tommy Boy wasn't around ... I would've bought his ... nevermind.
http://i232.photobucket.com/albums/e...s/Brakes28.jpg
http://i232.photobucket.com/albums/e...s/Brakes29.jpg

11) Test Fit.
http://i232.photobucket.com/albums/e...s/Brakes30.jpg

12) Okay now for the Brake Tool. Here is a pic for those of you still scratching their head.
http://i232.photobucket.com/albums/e...s/Brakes15.jpg
http://i232.photobucket.com/albums/e...s/Brakes16.jpg

13) You need to Screw the Brake Piston Back into its home ... funny. Yes people think you push this in when you actually have to turn it in. It screws back in.
http://i232.photobucket.com/albums/e...s/Brakes31.jpg

Tool Goes over it.
http://i232.photobucket.com/albums/e...s/Brakes32.jpg
http://i232.photobucket.com/albums/e...s/Brakes33.jpg

13) Now once you get the Piston Down, I recommend some good Lube. Brake Lube that is. This helps with some of the Squeaking noise and also helps put the caliper back over the brakes. Easy to slip on ... hehehe ... anyways.
http://i232.photobucket.com/albums/e...s/Brakes34.jpg

Lube the spots that come in contact with the Brake Pads (NOT THE SIDE OF THE PAD TO THE DISCS!!!)
http://i232.photobucket.com/albums/e...akes35copy.jpg

14) Okay dokey. Lets put the caliper back over and Put in the Screws.
http://i232.photobucket.com/albums/e...s/Brakes36.jpg

Just reverse the install and you will be done.
http://i232.photobucket.com/albums/e...s/Brakes37.jpg

Time for some Ice Cream.

Hope this helps many of you. [:)]

-Ray-

racer1735 07-04-2009 03:40 PM

Good show! When I did mine, I had a dickens of a time getting the springs on the top of the brake pads to stay positioned in the calipers. One side of the spring would want to 'walk' into the opening in the top of the caliper, thus pushing the pad sideways. Did this over and over again...frustrating!

captcomputer 07-04-2009 04:47 PM

Good writeup an nice clear (NIKON) pictures. [thumb]

Now lets add this to the sticky thread list.

tukaniSVT 07-06-2009 08:43 AM

I make em clear for everyone to see. Man was it hard to take pics alone with a SLR Nikon.

Ray
Posted via FF Mobile

scrammer 07-06-2009 09:29 AM

i have never seen anyone take the caliper apart to replace the pads. but hey, whatever works.

good write-up[thumb]

to all people that want to do this. that square shiny looking brake tool is an absolute must to have. the piston screws back into place. a normal caliper clamp will not work. some people use different methods to screw the piston into place, but for the price of the tool, its well worth it. it makes it so fast.

1-ST 07-06-2009 12:26 PM

Great write up with LOTs of excellent pictures. rep for you!

Is this in the How-to section yet? it should be.

sleepyboy 07-08-2009 09:02 PM

hey these are really cool pictures BUMP! Wow this should be in the How-to sections

SVTRSST 07-11-2009 12:06 PM

hey i didnt read any of machined rotors.. can someone explain if i really need to do that?, tukani?, anyone?

Focus112 07-31-2009 06:34 PM

i new something was fishy about the rear caliper, thanks a lot + rep

lightning2nd 07-31-2009 10:15 PM

nice job


All times are GMT -5. The time now is 10:57 AM.


http://www.focusfanatics.com/aboutus/copyright.asp