Focus Fanatics

Focus Fanatics (http://www.focusfanatics.com/forum/index.php)
-   SVT Interior Mods & Upgrades (http://www.focusfanatics.com/forum/forumdisplay.php?f=110)
-   -   How to: remove rear seats w/ pics (http://www.focusfanatics.com/forum/showthread.php?t=199523)

sunyfoci 05-18-2009 07:24 PM

How to: remove rear seats w/ pics
 
Since I was taking my seats out I thought I'd do a quick how to with pictures.

Time - about 10 minutes

Tools required -
T40 torx socket
T45 torx socket
Socket wrench
http://i190.photobucket.com/albums/z...m/IMG_4257.jpg

Step 1
From inside the car remove the two bolts holding the lower section of the back seat using the T40 socket.
http://i190.photobucket.com/albums/z...m/IMG_4258.jpg

Step 2
Lift up on the backside of the lower seat and remove it from the car
http://i190.photobucket.com/albums/z...m/IMG_4260.jpg

with the lower section out of the car you can replace the two bolts so you don't lose them.
http://i190.photobucket.com/albums/z...m/IMG_4262.jpg

Step 3
Using the T45 socket remove the mounting points for the 3 rear seat belts, middle and both sides.
http://i190.photobucket.com/albums/z...m/IMG_4264.jpg

It is necessary to remove the sides because you have to unloop the shoulder straps on the sides through the elastic, you could skip removing the two sides and just cut the elastic if you wanted to also.
http://i190.photobucket.com/albums/z...m/IMG_4265.jpg

Step 4
Open the hatch and remove the cargo cover by unclipping the strings attached to the hatch lid
http://i190.photobucket.com/albums/z...m/IMG_4267.jpg

Slightly lift up on the cover and pull it toward you, it will pop out now you can lift it up and slide it out.
http://i190.photobucket.com/albums/z...m/IMG_4268.jpg

Step 5
Push in the seat release buttons and flip both sides of the rear seat forward
http://i190.photobucket.com/albums/z...m/IMG_4269.jpg

The back seat should now look like this, with the lower carpet removed.
http://i190.photobucket.com/albums/z...m/IMG_4271.jpg

Step 6
In the middle of the two hinged seats you will see a bolt this holds the middle hinge for the seats.
http://i190.photobucket.com/albums/z...m/IMG_4273.jpg

Using the T40 socket remove this bolt and slide the metal piece it was holding toward the front of the car to remove it.
http://i190.photobucket.com/albums/z...m/IMG_4274.jpg

Step 7
On the left and right sides there are 2 bolts still holding the seats, use the T40 socket to remove them.
http://i190.photobucket.com/albums/z...m/IMG_4275.jpg

Step 8
Lift up on the right side section of the rear seat, with some effort it should pop out of the middle hinge and right hinge
http://i190.photobucket.com/albums/z...m/IMG_4277.jpg

You should now be able to remove this smaller section by pushing it to the side away from the larger seat section.
http://i190.photobucket.com/albums/z...m/IMG_4278.jpg

Pull the larger section out now and replace the bolts in the seat backs so you don't lose them

Replace the piece of metal and bolt in the middle hinge.
http://i190.photobucket.com/albums/z...m/IMG_4280.jpg

And you're done the rear seats are out of the car.
http://i190.photobucket.com/albums/z...m/IMG_4281.jpg

kjsoccerdude 05-18-2009 08:41 PM

I don't honestly see myself ever doing this, but very nice write up!

FocusontheZX 05-18-2009 09:49 PM

Very good write up... The people who do this though are typically going to take all the brackets out and do a rear seat delete. If you are doing this for some wiring, you can just do step one and remove the bottom seat bench. With that out of the way you have all the access you need to do your wiring.

ottotroll 05-18-2009 09:53 PM

nice write-up....actually, with any luck, I am picking up rear SVT seats to match the fronts I put in in April....

bonejob 06-04-2009 01:01 AM

Great write-up, but I have a question...
 
When I am driving, especially on the lunar surface streets of Madison, WI, I hear an infernal squeaking from the rear seat area. Just for kicks, I made my wife ride in the back seat yesterday on our commute to work. MIRACLE!! NO SQUEAKING! As soon as I dropped her off at her job and the rear seat was vacant once more, the squeaking returned. At the end of the day when I picked her up, I made her get in the rear seat again, and once again the squeaking disappeared. This problem seems obvious, right? Something in the rear seat is squeaking, and the weight of a person sitting on the seat stops it.

The trouble is, I have tried everything short of removal and disassembly of the seat to find out what is causing the problem. I tried moving the seat bottom up and down, that hinge does not squeak. Moving each half of the upper, no squeaks there either. Fold the seats down altogether, in cargo mode, squeak is still there. It only goes silent when the seats are up and someone is sitting back there.

Oh, and I thought of the seat belts, too. The reels do not squeak and I even tried fastening the belts with no one in the seat and that did not quiet the squeaking either. The only thing that quiets it is the weight of something substantial - like a human body.

Since you have completely disassembled the seats, I think that qualifies you as an expert on Focus rear seats. WHERE is this squeaking coming from and how can I silence it - short of permanently strapping my wife into the seat and never letting her out?

[?|][?|]
Thank you in advance for any suggestions.

SOHCTUNER 06-04-2009 01:15 AM

Maby you have mouse in the seat?LOL a Dog toy mouse LOL! also if you do remove the rear seats we typically remove the brakets and all bolts and even the seatbelts and seatbelt buckles. its up to the person if they want a rear seat delet i didnt.

sunyfoci 12-18-2009 01:15 PM

I get the squeak sometimes too after ive removed and reinstalled the seats i've determined its coming from the locking latch for the upper seatbacks if you don't bolt the hinges in just right they squeak like crazy, i usually loosen them up if they are squeaking, move them around a bit then tighten them back down and the problem is usually solved

CaptainChaos! 12-22-2009 01:29 PM

Just a thought, but if a squeaky hinge is the issue, perhaps a small dab of wheel bearing grease will shut the thing up. I've done this successfully on door hinges, just don't go crazy with it. A little dab will do ya.

pistolgripbmx 12-22-2009 04:42 PM

Good write up. It seems like a lot of people get confused when it comes to removing the back sections. This should help.

N4niner206 06-28-2012 07:33 PM

Thank you for sharing this!!! Repped.


All times are GMT -5. The time now is 03:37 PM.


http://www.focusfanatics.com/aboutus/copyright.asp