Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum

Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum (http://www.focusfanatics.com/forum/index.php)
-   DURATEC Performance (2008-2011) (http://www.focusfanatics.com/forum/forumdisplay.php?f=329)
-   -   HOW-TO: Mechanical CEL Fix for a Header (http://www.focusfanatics.com/forum/showthread.php?t=161467)

SYZ 05-29-2008 05:44 PM

HOW-TO: Mechanical CEL Fix for a Header
 
Well, there's always threads on how a newly-installed header has caused the check engine light to come on. Here's a tutorial to circumvent this problem. A tune can disable your rear o2 sensors, but in States whose smog stations plug into the OBD-II port, a disabled o2 sensor will instantly fail you for smog. This is a mechanical fix; it does not turn off or disable any of your o2 sensors.

Tools required:
Strong drill
1/2" drill bit
Vise (preferably)
Crescent wrench
Anti-seize copper sealant
Jack and jack stands


1) First off, you need to check how many o2 sensors you have.


http://i82.photobucket.com/albums/j2...ll3sensors.jpg






2) If you have THREE like in the picture, you will need to buy TWO packages of these:

http://i82.photobucket.com/albums/j2...lerpackage.jpg



There should be two anti-foulers in each package. Get these exact ones. You can find them at Pep Boys, Kragen and most auto parts stores. If you only have TWO o2 sensors in your exhaust manifold, then you will only need one package.






3) Now, you'll need a 1/2" drill bit, a vise and a fairly strong drill. Make sure your drill bit is sharp. You will need to drill a 1/2" hole using the drill bit through the anti-fouler, essentially opening up the hole that already present. For people that have THREE o2 sensors on their header, you will need to drill two of these anti-foulers. YOU NEED TO DRILL ALL THE WAY THROUGH THE ANTI-FOULER, OTHERWISE THE o2 SENSOR WILL NOT SCREW ONTO IT.

http://i82.photobucket.com/albums/j2...uler-drill.jpg

http://i82.photobucket.com/albums/j2...ing-fouler.jpg






4) Ok, so now you will want to disconnect and unscrew the #2 and #3 o2 sensors from the car. For those that only have two o2 sensors, you only need to disconnect the last sensor. You'll need to jack up your car to access the #3 o2 sensor, so take car doing that. Put it under a jack stand or two.



5) Take one drilled anti-fouler and screw it on top of an un-drilled anti-fouler. Use some anti-seize on the threads. Now screw the #3 o2 sensor on top of the the drilled anti-fouler. Use some anti-seize on these threads as well, but don't overdo it and slop it all over the sensor. Screw this double anti-fouler assembly into the header bung, using anti-seize on the threads again. (For those of you that just have two o2 sensors, do this step for the #2 sensor; you are done)

It should look like this:

http://i82.photobucket.com/albums/j2...o3o2sensor.jpg








6) Now take the other anti-fouler you drilled and install that on the #2 o2 sensor, using anti-seize. Here's how it should look:


http://i82.photobucket.com/albums/j2...ndo2sensor.jpg


And just for clarification, do NOT put any anti-foulers on your primary o2 sensor. That one monitors your engine and has nothing to do with emissions. LEAVE IT ALONE!!

http://i82.photobucket.com/albums/j2...o1o2sensor.jpg






7) Make sure everything is tightened down. Unplug the battery for 10 mins. Plug it back in, lower the car from the jacks and take it for a spin. Hopefully you have the same luck as me and your CEL should not come on again.

besthaticouldo 05-29-2008 05:55 PM

this works too...ive seen it in person. sick ass set up

slickzx3 05-29-2008 06:10 PM

very nice write up syz, good pics,easy to understand, perfect.

alk3civichater 05-29-2008 06:20 PM

Nice write up man! looks pretty simple! [thumb]

alk3civichater 05-29-2008 06:20 PM

But it could be that you make it look easier than it is too! lol

homeboyjames 05-29-2008 06:28 PM

Good write up might have to do it. so a tune wont get me past the emissions?

SYZ 05-29-2008 06:34 PM

It depends on which State you live in and the smog station.

SALEEN_N2O 05-29-2008 06:35 PM

cool! i was thinking bout doing this but didnt know how i would do it


thanks for the how to!

Jonathan

homeboyjames 05-29-2008 06:37 PM

Quote:

Originally Posted by SYZ (Post 2149868)
It depends on which State you live in and the smog station.

i ant gatta go till 2009 but its supposed to be done in 08 but than in 07 they said it would be done and its still here wat BS.. around here 7 countys make u do it the other dont so i dont see the point

Klondike 05-29-2008 06:38 PM

really good write up, may have to do that when i get a header, dont plan on tuning for a while


All times are GMT -5. The time now is 05:10 AM.