Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > MK1 Focus > How to: Paint your Headlights 2005

MK1 Focus The place to chat about general questions, window tinting, exterior body, interior and lighting upgrades for the first generation 2000-2007 Focus.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: How to: Paint your Headlights 2005 Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-12-2013 11:59 AM
brady2005 I have painted the inner headlight bezel on a few cars, I preset the oven to 170 and left it in there for 10 mims and got it apart.

Just a FYI ( and I havent read the full thread so this could have been mentioned already) but when you car goes to a bodyshop to be repaired/painted, lets say there painting your doors, so your headlights are still in the car as opposed to a fender where they would remove them (at least a good shop would , ty shops would mask them), after you finish spraying your clear, you "bake it" which means they turn on a bake cycle to harden the clear, which can be anywhere from 150- 180 degrees, putting your lights in the oven is not going to damage a single thing unless your above that range and leave it in there for too long. Another good thing to do is clean your headlight covers prior to putting them in and dont touch them with your bare hands prior to putting them in, use gloves or a clean towel. If they are left in for too long and you have had your sweat dirty greasy hands on them, it can create a hot spot ( just like how you dont put your fingers on a light bulb your installing) and create cracking or crows feet in the lens.
Just figured id mention that for all the people who were worried in the first 5 pages, or worried with there HID'S as they get baked at a repair shop in the booth as well, the only thing with HID'S is tue wiring that could be damaged only by disassembling or reassembling. HID's emit far more heat than 170, so the wont get damaged by the heating process.

HAVATER!
07-10-2013 11:57 PM
GreySkorpion The diffuser caused a huge headache, it got "baked" on with the first times I used the headlights and made the inside in the lights smoky, had to open them back up, clean out the residue/film from the snoke and reseal. In the end I was happy. They were new headlights and fogs I installed BTW. Just didnt like the chrome look.
07-10-2013 11:42 PM
Fluffy6079 Looks awesome! I never even thought about painting the diffuser. After seeing your car, I think I should have restored my fogs too. I do still have the sanding pads...
07-10-2013 11:36 PM
GreySkorpion ^^^Looks good on LG!! I did mine but painted the center light diffuser as well:

[IMG][/IMG]

[IMG][/IMG]
07-10-2013 06:51 PM
Fluffy6079
Wow...

Man, this worked out great! Looks heaps better.

Before


After


I also tried a Turtle Wax restore kit to mixed results. Please ignore the rest of my dirty, beat-up car.
03-12-2013 12:02 PM
mishka has anyone tried it yet?
I want to paint my housing black or maybe dark blue in the style of TI lights. It costs far too much to buy lights.
01-07-2013 10:30 AM
Drumr90 Ye idont see why not unless they changed plastic material.
01-07-2013 09:45 AM
jimpatrick you guys think you could do this with a 2013 focus?
08-30-2012 03:21 PM
Drumr90 Posted via FF Mobile
I put a glove on and slid my finger around headlight to make it look factory.
Ur way works to man.
08-30-2012 05:24 AM
LikwidZX5 Using rubber butyl is much easier than silicon, gives a much better end result too
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:13 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat