Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Forced Induction > JRSC rough idle with FC TB?

General Forced Induction The place to chat about turbochargers, superchargers nitrous systems and custom engine fabrications.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: JRSC rough idle with FC TB? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-18-2005 02:11 AM
titan this is great u have anwserd my question of wether or not the FC TB will fit the JR blower.but now i have another question asumming your usen the 65mm....will the 70mm fit on the JR and can you get the adapter for an auto to work with the 70mm?
04-17-2005 10:26 PM
dBlast My car seems to have trouble finding idle. It starts somewhere between 1K and 2K then drops to about 1050 then below 1000 it starts sputtering to point where I have to help it along with some gas to keep it alive. The FC TB was closing all the with the car unboosted mated to the stock intake manifold and it had no problem with idle. I'll try fiddling with it some more tomorrow. My friend is bringing over a JR TB to swap out to see if the problem goes away.
04-17-2005 09:14 PM
goinloco1 pull your air intake off and look at the butterfly in the tb. should be open a little.
adjust the idle screw until it s, disconnect the batt for a little while, reconnect and start the car and drive it a little while (needs to relearn).
should clear up the problem. sounds like your butterfly is closed all the way, starving the motor for air.
04-17-2005 10:47 AM
joebuddenZX3 hey man, how'd you like the jrsc, does it really give you a good kick at WOT. Are you happy or mad about dumping all that money into it. I just reserved an install date on mine in two weeks!
04-17-2005 09:35 AM
jezwald1016 maybe check to see if your iac solenoid is working,then maybe check your egr valve,disconnect hose to egr valve at idle and see if there is vacuum on hose coming off the egr solenoid,if there is then the solenoid is bad,had this problem before and disconnected this hose and it smoothed out and put a new solenoid on and was good then on...also maybe double check all your vacuum hose connections..and the two hose clamps at the blow off valve... retorque sc and intake bolts after heat cycle....hope this may help...jess
04-16-2005 09:04 PM
dBlast
JRSC rough idle with FC TB?

I just finished installing my JRSC and now my 2000 ZX3 has a rough sputtering idle. It seems ok with the throttle open, but as soon as I let off on the gas it starts to sputter and then stalls. I have no CEL or vacuum leaks (I think.)

My FC TB was fine before the JRSC was installed. With the throttle closed the FC TB has 3 bypass holes to let air through to maintain idle. This was fine when mated to the stock intake manifold which has a sloted opening to accept the bypass holes. The JRSC just has one hole slightly larger then the 3 small holes on the FC TB. Is this mismatch the cause of my rough idle? Has anyone else had this same problem with this combination?

I used the same gasket on the FC TB as was installed on my stock intake manifold. Could this gasket be leaking and be the cause of my rough idle? Any ideas?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:37 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat