Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus SVT > SVT Performance (2002-2004) > Catalytic Converter modifications

SVT Performance (2002-2004) The place to chat about any 2.0L SVT DOHC Zetec engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Catalytic Converter modifications Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-16-2013 01:37 AM
s0B0Ta I took my cat pipe off the car, took a grinder, opened it up like a sardine can, took the metal honey comb out and the ceramic top one out too, welded it back up, called Tom and made it into an Off Road Pipe.
But then again, i do live in a county where emissions testing is not mandatory :D
Thanks Tom!
04-30-2013 01:39 AM
1turbofocus You will have to just strip/brake the bolts off , its very common , then drill and use bolts and nuts

Tom
04-29-2013 07:24 PM
smallblockfever PROBLEM SOLVED
HUGEEEEEEEEEEEEEEEEE thanks to Tom for the info, advice, and know-how he provided to me. 'Twas invaluable.

What I ended up doing was relocating the bungs. I relocated a bung onto the side of my header right when pipes converged into one, right before the flange to the cat. The sensor is now mounted approximately 5-10 degrees above horizontal and is totally clear of any possible complications with the oil pan. As for the rear sensor, it seems that my wires were only stretched and not actually broken, so I straightened the sensor and plugged everything up. Couple of days later the CEL went away!!

Now I had bought a spare cat to replace the one on the car (one on the car is cracked). I welded bungs to the new-to-me cat to fix the rear problem as well by grinding down the lip near the rear OEM location and welding a bung in similar fashion with my new front mount.

Only problem I have now is I cannot for the life of my get the old cat off... Bolts are fully rusted, and the bracket holding the cat to the car is snapped in half so the entire exhaust moves around when I try wrenching on it.

If anyone has any tips on that, let me know. Otherwise it is gonna stay on the car until it becomes absolutely necessary to remove the cat.
03-31-2013 08:04 PM
smallblockfever so it has to stay 10-15 degrees above horizontal?
is there no issue with the catalyst being messed up by rewelding a new bung elsewhere? The heat from the weld won't alter the catalyst?
03-26-2013 02:12 AM
paulg127 Be sure to adhere to the usual tip-down, 10-15 degrees minimum from horizontal.
03-25-2013 11:22 PM
marcanjelo7 it's possible. the one I bought from a member had their rear o2 relocated to the side.

03-25-2013 09:27 PM
sleepyboy I know some have moved them on the ORP's due to them getting broken, I don't see why it couldn't be done on the cat.
03-25-2013 09:25 PM
smallblockfever
Catalytic Converter modifications

Has anyone had luck relocating the 02 sensor bung on either the header or the cat? I'm going to replace them because I snapped them both. I figure that if I can eliminate the problem from the get go then why not?

I can take care of the header easily, but the cat is tricky. Has anyone had luck with plugging the stock bung with a plug and re-welding a new bung in a less interference-prone area?
I'm nervous about bringing a welder anywhere near an SVT cat... Guidance and suggestions are greatly appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:11 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.