Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > PS pump removal

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: PS pump removal Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-20-2013 09:10 AM
Bruce Almighty Thanks for the info, I was going to try that... but knowing it worked for you I will do it that way
03-20-2013 07:30 AM
dustin102 Just an FYI... I just swapped out my thermostat last weekend. Remove the belt. The there a 4 bolts holding that p.s. Pump On. The one behind the line will be the last bolt to come off. I was able to get an open end wrench on that bolt and thread it off. With out removing the line. The oil reservoir will just pop off the pump when the top to bolts are off.... Just take it off and drain it to get it out of the way. This is a PITA I spent maybe an hour and half on that bolt getting it out then back in. but it is possible. :eek:

Sent from my Galaxy Nexus using FF Mobile
03-20-2013 06:28 AM
Bruce Almighty I can position a 6'' wescot wrench on it, but I'm afraid I'll break something when pulling. Guess I'll have to try harder and maybe find me a flare nut wrench (18mm)

I will use that t-stat writeup, but my engine is the 2.0, should be similar.

Thanks
03-20-2013 12:28 AM
elsolo That's a neat writeup for thermostat.....

Back to the power steering pump:

There is no trick to the hardline, other than make enough room for yourself and use a flare nut wrench. (6-point box end wrench with slot cut out).
03-19-2013 09:21 PM
VillageT Here is manual on 2.3 dtec-should be the same
Removal and Installation

NOTE: The thermostat and thermostat housing are serviced as an assembly.

Drain the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section.
With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
Remove the accessory drive belt. For additional information, refer to Section 303-05 .
NOTE: LH shown, RH similar

Remove the two power steering hose bracket retaining nuts and position the hose and brackets aside.

Remove the cooling fan motor and shroud. For additional information, refer to Cooling Fan Motor and Shroud—2.3L in this section.
Remove the four A/C compressor bolts and position the compressor aside.

Remove the hoses to the thermostat housing.
Release the spring-style clamps.
Twist and remove the coolant hoses from the thermostat housing.

Remove the bolts, the thermostat housing and the thermostat as an assembly.

NOTE: Lubricate the thermostat housing O-ring with clean engine coolant.

To install, reverse the removal procedure.
Fill and bleed the cooling system. For additional information, refer to Cooling System Draining, Filling and Bleeding in this section.
03-19-2013 07:58 PM
Bruce Almighty
PS pump removal

I need to know if there is a trick to remove the hard line from the PS pump so I can remove it from the engine bay and get to my t-stat housing (my main job).

To date I removed: belt, PS reservoir, light housing, sensor connector and 2 bolts of the PS pump. I put a small wrench on the nut of the hard line and pull has hard has I can, but it wont move.

Thanks for the help, I need to get this done so my wife can have her car back.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:57 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.