Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > motor SVT

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: motor SVT Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-13-2013 03:32 PM
Magus2727 Passenger is a little more involved then just 2 bolts. Unless the SVT is that much different on the passenger side, there are a few covers and brackets you have to remove. Coolant tank is also usually removed (but not unhooked). Should have stickies...
02-13-2013 02:52 PM
whimsicalpouch2 alright alright sounds good thanks. i don't have to jack up the engine/trans too much right? just enough so its supported? and its only like what 2 bolts for the passenger and then 4? for the upper trans?
02-10-2013 04:56 PM
whynotthinkwhynot You use a block of wood to span the oil pan so the weight is distributed on the sides. That's given in every manual. I prefer plywood myself, but if your jack's saddle is big enough then you can use a 2x4. You should do the same thing for the transmission- it is not wise to jack up on cast aluminum without having wood in there to absorb the hardness of the saddle.
02-10-2013 04:21 PM
whimsicalpouch2 isn't it bad to lift the engine by putting a jack on the oil pan? wouldn't that crush it and make me get a new oil pan??
02-10-2013 03:18 PM
whynotthinkwhynot Jack under the trans for the trans mount, and under the oil pan for the front engine (passenger side) mount. Just make sure that you are not putting your mount bolt in a bind when tightening. You will damage things if you pull the motor up to the mount with the bolt(s).
02-10-2013 02:53 PM
whimsicalpouch2 i'm not worried about vibrations, i like the stiff ride my car already has and the vibrations won't affect me
02-10-2013 02:53 PM
whimsicalpouch2 would a jack under the transmission be able to hold the engine in place while i would do the upper trans mount then followed by the passenger mount?
02-10-2013 12:53 PM
whynotthinkwhynot From our vendor Central Florida Motorsports.

They warn you that poly mounts will cause vibration and are race only, however, I have poly mounts on my engine and I don't think the vibrations are all that bad. Yes, it does vibrate at idle, but as long as you do the mount installation correctly- it's not horrible. As soon as you give the car some gas- no more vibration. Acceleration is more immediate.
02-10-2013 12:51 PM
whimsicalpouch2 where can i get the new bushings for the 2 mounts?
02-08-2013 04:25 PM
ViperThreat
Quote:
Originally Posted by whimsicalpouch2 View Post
how easy is it to change the bushings in my passenger mount and upper trans mount to poly mounts?

mine need to be changed, i recently changed my dogbone, and i feel like that'll wear out faster with the other 2 mounts being bad aswell seeing that they are stock with 171000.

i would rather change the bushings out but if its cheaper than buying the whole mount, id rather do that
Getting them in and out isnt very difficult, just put a jack under your engine to hold it up while you work on them

Pressing the new bushings in however is a bit difficult. you may need some sort of press to do it.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:00 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.