Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus First Generation > ZETEC Performance (2000-2004) > question about exhaust

ZETEC Performance (2000-2004) The place to chat about any 2.0L Zetec engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: question about exhaust Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-28-2013 11:39 AM
redfocusdrver i would say to go with the fswerks 4 -1 header and flex, but idk if they make that for zx5.
01-28-2013 11:01 AM
zTimbo I went with the OBX, for the price I was pleased and it served the purpose I wanted it for(to be able to remove the catalytic converter). It's a decent piece, nice thick 3/8" flanges, all TIG welded.

Mine came with 2 provisions for o2 sensors and a provision for the EGR, but it was threaded wrong. This wasn't a problem for me but could be for some who don't posses the skills or equipment.

I unscrewed my OEM EGR tube adapter from the OEM catalytic converter and cut the threads off. This is to allow for the adapter to at the right height as if it was screwed into the OEM converter.



Then I welded it onto the end of the bung that had the wrong threads that OBX supplied.



I welded 2 6mm nuts onto the header tubes so I could reinstall my OEM heat shield. I had to trim it up a good bit for it to work which I was ok with because I was mainly concerned with how close everything is and wanted the most protection. I also wrapped the entire header with exhaust wrap.

The OEM dipstick had to be unbolted from its bracket an zip tied(for now until I find a solution) away from the header tube. I also tweaked the brackets for the power steering line to provide a little more space between it and the header as I read some people had problems with it getting hot and failing.

Hope this helps
01-23-2013 01:07 PM
sgtsmasher forget the obx, find a used svt header, cat and flex pipe, buy the cat and flex off this site http://www.mandrelexhaustsystems.com/servlet/StoreFront... and you would need the power steering line from the svt, or off c-f-m.com you can get the relocatioin line. you also need an oil dipstick from the svt. and you can even get a decently priced exhaust 2.5" diameter. i went the cheap obx ebay route, worst waste of money ever...the svt header is a tad bit not on the cheap side but you get the best results as far as power goes and it wont be as loud as the obx, and the fitment as stated above wont be an issue.
01-23-2013 03:30 AM
TerryB Related thread.
http://www.focusfanatics.com/forum/showthread.php?t=306485
01-23-2013 12:17 AM
zetecDon The only thing I am going to say is that you pay for what you get. OBX exhaust systems are sold cheap for a reason and that is there quality isn't always the best. Will it fit? More than likely, but most of the time I have seen and heard is that they have always required modification in order to fit properly. And even when it was made to fit properly it didn't always line up correctly on the manifold.

Now as for getting an exhaust off of Ebay. OBX does make a decent exhaust but a lot of others on Ebay are not worth the price you pay for them. What I mean is that the quality of the metal isn't the best and sometimes the flanges, hardware and welds rust through quickly leaving you with an exhaust that will need repaired in a year or so.

For an exhaust, I would buy one used off of someone on here or I would search around for a well trusted and known brand like MRBP, TruBendz, Borla, Magnaflow etc... Plus you can always go to Youtube and hear how those exhaust sound so you can find the one you really like.
01-22-2013 11:05 PM
02silverbullet
question about exhaust

so im going to begin modding my zx5 and im looking into the obx racing 4 1 ss exhaust header and down pipe for now and a volant intake what are your guys thoughts on the exhaust ive heard lots of good things about the intake but not sure about the exhaust what is the good and the bad i can get the exhaust for 179.99 on ebay and remember im a college student on a limited budget...thanks for any input!
here is the link to the ebay site

http://www.ebay.com/itm/OBX-Racing-4...f29c47&vxp=mtr

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:22 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.