Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Technical Chat > Special Tool Required for Brake Master Cylinder Replacement?

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Special Tool Required for Brake Master Cylinder Replacement? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-18-2013 10:28 AM
bennyfocus Nah its not that bad, we had one come in from the body shop that they couldnt get a firm pedal in after a slight fender bender. They replaced the master twice and the booster before they brought it to us. We tried to bleed normally, then tried to bleed it with our power flush machine just to be sure there was no air. After that we did the abs bleed which as simple as selecting it from the functional test menu on our scan tool, keeping your foot on the brake pedal while it does its thing and after about a minute its done without the need to open bleeders or anything. Obviously though if you have no friends with access to a good scanner you will have to pay someone if it comes to that however I doubt you'll have any issues.
01-17-2013 12:23 AM
amc49 Unless the ABS was activated during low fluid and swallowed air (should be impossible, but somehow people figure out how to do it!), then it is transparent to the system and normal bleeding should work fine. I would AVOID powering it on during bleeding if possible, only do it when necessary or forced............I know I never do anything special for it. Once you get air inside the ABS itself you are in much more trouble from what I've seen.
01-16-2013 01:19 PM
elsolo Unless there was a change between 2003 and 2005...

The service manual just calls out for traditional bleeding methods, nothing special or proprietary.
-Jar of brake fluid and a hose connected to the nipple at the caliper.
-Pressure bleeding from the reservoir
01-16-2013 07:34 AM
bennyfocus No sleepyboy is right, on some occasions you may need a scan tool capable of bleeding the abs out. Personally I have only ran into that issue once or twice. Also something else I think they listed as "special equipment" is a pressure bleeder, I think they prefer you pressurize the master then crack open the bleeders. As long as you bench bleed the master before you put it on then bleed the system like you normally would on any other car you should be fine.
01-16-2013 06:56 AM
coldbear X 2 on the scary manuals.
01-16-2013 06:02 AM
whynotthinkwhynot No, it's probably bench bleeding tubes. The master cylinder should come with directions on how to bench bleed it. You might also want a vacuum bleeder kit, but you should read the directions because bubbles in the lines on a vacuum bleeder are not a cause for alarm. It will actually pull air through the threads on the bleeder nipple.

Open up your new master cylinder and read the directions. Haynes Manuals are meant to confuse people and scare them into taking cars to a mechanic instead of actually giving customers technical knowledge of vehicles and systems. It makes the manual easier to write.
01-16-2013 01:13 AM
sleepyboy I imagine it would be a scanner or something like that to activate the abs solenoid? Hopefully someone else will chime in with the right answer.
01-16-2013 01:07 AM
focusgg
Special Tool Required for Brake Master Cylinder Replacement?

Hi All,

I need to replace my brake master cylinder on my '05 ZX4. The Haynes manual says I need 'special test equipment' to bleed the system after the master cylinder is installed on cars equipped with ABS.

Does anyone know what this special test equipment is, or how I can get around using it. Obviously, I want to do a proper job to ensure safety, but if there is a DIY trick, I'd like to know.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:00 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat