|01-13-2013 01:55 PM|
|gondorian||I had this same problem a few weeks ago and the locksmith was able to cut a key just from the VIN. He then had to plug some computer device into my OBD II port to make the car accept my key. It took all of 15 minutes, but cost a couple hundred for two new keys.|
|01-12-2013 04:58 AM|
Are we saying here that if I successfully programmed a third key myself, the the first two I already had HAD to be different IDed masters? Is that a normal Ford process to give two masters with a new car? I had always assumed anything beyond the original key was a clone and there was only one ID kept by PCM even though it can do more if needed. And which of the masters was the one cloned?
Sorry but you got me awake now..............LOL.
|01-12-2013 01:04 AM|
PATS Master Key vs Clone key
A PATS key has an RFID chip embeded in the handle. When you insert the key into the ignition the computer reads the chip and if it's ID matches one of up to six IDs stored in it's memory your computer will work with it. If the cut pattern of the key matches the cyclinder then you can rotate the ignition switch and all works. If the chip does not match one of the 6 stored IDs, or if the computer is unable to read the key's chip, your computer will not start the car even if the key rotates the ignition switch. So even if your new key does have a PATS chip, if it is not paired with you car's computer so it will not work.
There are a couple of ways a locksmith can make a key for you:
DEFINITION: A "Master Key" is just a key whose ID has been paired (accepted and stored) into your car's computer.
1) Clone a master key: The key blank for these have an even fatter handle and do not have a FORD logo. After the locksmith cuts the teeth pattern, they read the ID from a "known working" key and write it to the newly cut key, hence you have a clone of the original key. In my experience these clones stop working in a couple of years. Also as far as your PATS system is concerned this cloned key does not count as a second master key. Some clones have a battery that requires replacing.
2) Make a new master key: A new OEM blank is used, and it's chip already has an unchangable ID. The locksmith cuts the teeth and the key's ID is paired to your car's computer.
3) Pairing a new master: If you have two master keys (not a master and it's clone) you can pair it yourself. If you do not then the locksmith can connect a computer to your car and pair the new key in about 10 minutes.
I went through all of this on my Focus when the cloned master died. In the San Antonio area it cost me about $35 for a locksmith to create a new master from an OEM blank and pair it to my car.
|01-09-2013 02:44 AM|
|amc49||Milton, I could find nothing in that 10th post, maybe I'm blind. Regardless, I was speaking obviously off the cuff rather than out of knowledge........|
|01-08-2013 04:36 PM|
Even if they don't want to keep blanks, how much data and trouble is it to give me the tumbler codes so I can get a key made somewhere else.
|01-08-2013 04:33 PM|
At least towing to the locksmith shop its closer to my home.
At this rate, I might just let the wrecker keep it and call it even.
It's really not worth that much money.
|01-08-2013 03:39 PM|
So they sent the car up to the dealership to get programmed (without telling me how much or asking if they could). Dealer says they got it started once, then it goes back into lock mode. FFS.
Anyways, the dealer's cost to reprogram the new key to the system is cheap so I said try it again and if not then tow it to the locksmith I found in my town. If it comes to that, I'll figure out if its worth it to put the old ignition in and get him to make a key or to work with this salvaged ignition/key.
|01-08-2013 03:56 AM|
|Milton||Amc49, you are incorrect, they are NOT all clones. For the definitions of a "master" key and a "clone" key, search for the thread "Key troubles.." and read post number 10.|
|01-06-2013 01:29 AM|
You have no choice but the locksmith...
ALL makers of cars make the dealerships use the 10 year or 7 year policy not to sell a new car, but to keep inventory at a certain level.
If your part is 10+ years old, 99% of the time its Junkyard or Autozone...
Can you imagine if I went to a dealer and had a fit over Ford not having a Key for a Model T in stock?? hahahah
BUY your keys on eBay then give them to the locksmith, GET 3 keys Total..
He will use a cheapo key to get the right fit from the door, then transfer that to the ignition, then program the keys
|01-06-2013 01:09 AM|
|amc49||Uh, they're all clones after you have one..............I'm with elsolo, I keep 3 on hand at all times so that can't happen, if one lost you can still pull the rabbit out of the hat.|
|This thread has more than 10 replies. Click here to review the whole thread.|