|02-15-2016 07:07 PM|
When is the 16 write up coming
|10-21-2014 02:17 AM|
Never mind, In the meantime i took measurements and did mine.. The car feels like solid steel now!
Thank you for the reply.
(focus mk2 DA3 2005-2011).
|10-20-2014 09:56 PM|
Αυτό είναι ένα καθαρό crossmember μόνο για την εξάτμιση. απόθεση, συγγνώμη για την καθυστερημένη απάντηση, sec άρρωστος να μεταφραστεί σε Ελλάδα
|09-10-2014 09:42 AM|
Hello, i'v seen that you had to remove a mid-chassis bar when changing exhaust on the ST. Does yours have one and can you measure the length from bolt to bolt?
|04-18-2013 07:24 PM|
Personally I am looking for 2 specific types of tunes.
1. Eco Tune for daily driving.
2. Full on tune for track days on road courses.
Both of these keep in mind to be used on a completely bone stock Focus ST. I do not plan on doing any "real" mods to the car. There will be some but they will all be OEM upgrades from Europe.
|04-08-2013 12:03 AM|
It is running at 12:1 compression vs 9.3:1 of the ST, which is why even with up to 20 PSIG of boost pressure only makes 93 more horsepower at the crank shaft as the naturally aspirated engine as a stock baseline.
The higher compression is more efficient at extracting power out of the fuel when you're out of boost on the turbocharged application.
Without tuning however there is only so much can be gained on the stock calibration.
The N/A powered Focus also weighs 275 lbs less than the EcoBoost powered ST, 3223 lbs is the estimated curb weight of the ST, vs 2948 lb for the N/A hatch.
It should be feasible to get the n/a engine up to around 200 hp or slightly over for the 5MT, but until proven otherwise the DCT models are constrained to 180 lb-ft of torque per the rating on the gearbox by Ford and Getrag (250-280 NM).
|04-07-2013 11:13 PM|
I too am Happy to see COBB in here. I used some of there stuff on my MS6. Great products. And yeah ECOBOOST motors...flat out kick ass. I struggle to even use Ecoboost anymore...its just Fords boosted engine, there is nothing ECO about it when I drive my ST or my F150
With all do respect to frinesi2.....The logic you are using is understandable, trying to think outside the box, but you would have a small fortune getting the Duratec motor up to the point of the ecoboost is already. I would start with the best and add my time and money from there if you were really serious in building a monster. This comes from one of the many guys that has dumped a ton of money into my cars in the past.
|04-07-2013 10:05 PM|
|04-06-2013 05:41 PM|
The standard Durtec does not hold a candle to the Ecoboost motors. You would be spending a ton of money just to match it potential. Its cheaper to just trade-in your standard Focus and carry over the negative on the ST.
Your payments would be higher but hey, you knew the ST was coming, you could have bought a cheap car just to hold you over. Save money and put more down on the ST with a lower principle and payment.
Boo-hoo sucks to be you wishing Cobb make stuff for standard Focus when they've only dealt with boosted cars their entire existence, good luck with that.
Face it you bought a slow car, so live with it.
|01-10-2013 11:25 AM|
|Black00ZX3||Great torque numbers still wishing you guys made something for us non ST owners.|
|This thread has more than 10 replies. Click here to review the whole thread.|