Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Technical Chat > Clutch slipping some; master cylinder / relief valve?

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Clutch slipping some; master cylinder / relief valve? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-25-2012 02:49 PM
LugNut Luck not on my side -- for this, nor the $250MM Powerball drawing.

Did the work yesterday morning. 11 month-old fluid came out rusty color, but not lumpy. New clutch master cylinder was identical to the original (LuK brand). No difference in the clutch operation, darn it.
11-19-2012 08:11 AM
sailor The identical to stock master cyl. I just installed was an LuK (German), so that could match stock. Good Rep. AFAIK

Hope you get Lucky, and can keep it going for them cheaply.
11-19-2012 07:16 AM
LugNut Thanks -- I will likely try replacing the master cylinder first ($35 locally).

I found my old pics of the flywheel. It looked quite good after a light refinishing, and from experience my clutches have done well with such. So if not the master cylinder or defective materials, it's looking like driver error. That's bad news because they are needy, and are to keep this gift car longterm.

The clutch set was a LuK. Anyone had bad luck with Luk?
11-19-2012 04:09 AM
amc49 Uh, technically there IS a relief valve, the compensation port at master, if clogged or corroded it could easily hold the clutch fingers down. I don't screw with hydraulic clutches much but the cylinders are same basic design as brake and I've seen plenty of brake cylinders with that port clogged pretty solid to lock brakes up and car won't budge.

Worn disc most likely.
11-17-2012 04:55 PM
sailor Agreed, worn matches the symptoms. We don't know mileage or condition/replacement of flywheel yet when the clutch was "replaced".

New Clutch on an old, worn flywheel seldom lasts long....
11-17-2012 04:24 PM
jetrinka Worn clutch. The pressure plate fingers provide more than enough "push" to return the pedal effectively. There isn't any relief valve either. Its just a straight shot out of the master to the slave and back again.
11-17-2012 01:27 PM
LugNut Hmmmm ... I did look up under the dash to look for sloppiness in the pedal, etc., but don't remember looking at/for the spring. Will definitely notice the next time, but that will likely be next weekend or so if I replace the master cylinder.

Thanks.

Any others' experiences/"external" repairs for this problem?
11-17-2012 12:28 PM
sailor From VERY recent experience (grin), I learned that the clutch return spring can be missing for a LONG time (broken off & disappeared) WITHOUT much in the way of symptoms.

Occasional slow engagement (slipping) and occasional need to lift the clutch pedal to engage the cruise control.

Installing a spring when the leaking master was replaced solved the issues....

Worth a check B4 diving deeper...
11-17-2012 11:22 AM
LugNut
Clutch slipping some; master cylinder / relief valve?

The 2001 SE Sedan, with the SPI that I rebuilt and put in a new clutch about a year ago, now has a slipping clutch. The driver (not me) is very experienced with manual transmissions, so I thinking it's not from driver error.

I just had the car for a bit this morning. There's no leakage of oil from the vent at the bottom of the bellhousing, so a bad engine rear seal is not likely.

From the FSM, the hydraulic clutch is not adjustable. Clutch pedal operates correctly. Hydraulic fluid in the shared reservoir (brakes and clutch; not a better idea!) is clean and full.

From a test drive, it is slipping some in all gears, but does slowly engage. If not a bad clutch set ($700+ by a shop), my other guess is a bad/clogged hydraulic pressure relief that is slowing the release of the throw-out bearing. I'm also assuming the relief valve is part of the master cylinder.

Sound possible? Or better yet, solved the same yourself?

A new master cylinder is only $35, but a pain to install. I see this good thread on how to do it:

http://www.focusfanatics.com/forum/showthread.php?t=243148

Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:18 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat