|12-27-2012 05:54 PM|
|gondorian||So I've decided to replace the whole suspension because all the bushings are shot and seized to the bolts. After having a one go at it the only way I'll get these bolts out is by cutting or melting them so that I why I'm replacing everything. I hope to have all my parts in by next week and then I will put up plenty of pictures of everything I'm doing. :-||
|11-15-2012 04:22 PM|
|Missourileo||Here's is some advice from experience. Sawzall and a bunch of good blades. Get new control arms and bolts, then enjoy a few cold beers.|
|11-15-2012 12:21 PM|
|BigRed03||^this. and order all parts through steve at toulsey ford. 10% over stocking fee for OEM parts. you'll thank yourself.|
|11-15-2012 11:15 AM|
At that kind of mileage, I would do the dampers too. Remember, the wagon dampers are different than all other foci.
The alignment probably won't help your rear end hop. This is more likely a symptom of blown dampers (lack of control of wheel motion), or sway bar binding (additional uneven spring rate).
|11-15-2012 10:25 AM|
So y'all are right. I went to the local ford dealer to order the bolts and see if they sell the bushings. They don't sell the bushings, only the whole control arm. I decided I'd look for a bushing before I got a whole new arm, but after finding some on rockauto I had to measure the bushing to see what size it is. When I was measuring I noticed that there is a groove that holds the bushing. Getting the old one out wouldn't be too much of a problem, but pressing a new one in would be pretty impossible without something breaking in the process (probably the bushing.
Now I've decided to do the smart thing as wrc_fan suggested and get two new arms. While I'm down there I'm wondering if you think I should replace the coil springs, which look rather worn, or if there is anything else that would probably need to be replaced after a couple hundred thousand miles. Here are some pictures:
Thanks a lot y'all, this forum is proving to be very helpful :)
|11-14-2012 09:56 AM|
I'm doing both sides of course. I just trying to figure out the best course of action before I start. I don't want to drive around with the broken bolt and I can't leave my car at work or in my friend's shop, which are the two places I have enough tools for this sort of operation.
This all started because I was experiencing some rear hop, and I figured an alignment should help. Right now my plan is to replace both bolts and bushings and get it aligned, then do the whole rear suspension next summer once I get the funds. I'm also getting sick of rust so I may take a wire bush to most of these parts while I'm at it and put rustoleum or bedliner on them.
|11-14-2012 09:39 AM|
Thats the cam bolt/bushing for the rear alignment. Pretty sure Steve at Toulsey can get these. If not, its honestly easiest to just replace the whole arm and bolts. Bolts through bushings will need to be cut out.
snow/salt, FL rules for that. Also, no emissions!
|11-14-2012 09:25 AM|
You could, but there is not (that I'm aware of) an aftermarket OEM style bushing for the car. Ford and the 3rd party suppliers only sell arms. Maybe I'm wrong here?
There are aftermarket performance bushings available. I think it would be easiest to remove the arm from the car to install. Also, I cannot advocate doing just one side of the car, it would make the handling pretty wonky, maybe unsafe. Both are my opinions, YMMV.
|11-14-2012 08:59 AM|
|gondorian||Could I just cut through the old bushing and the press in a new one after I get the old bolt out? Or is it too soft to press in a new bushing correctly?|
|11-14-2012 08:54 AM|
The opposite end of that control arm is usually the one siezed in place. That is one reason to be glad I'm not in Michigan any more. Lots of rust underneath there...
Maybe try an air hammer to punch it out? Here's the general problem with this design, and you'll see it if you search. The bolt shank becomes one with the inner shank of the bushing. So you can't get the bolt out, and the bushing is still working, so it absorbs your attempts to pound the bolt out.
And, if you do get the bolt out, but damage the bushing, you'll be even worse off trying to get the outter one to remove the whole control arm.
My advice, though its probably not what you want to hear, would be to pick up two new rear control arms, hardware, and swaybar end links, then go to town with a cut off wheel.
|This thread has more than 10 replies. Click here to review the whole thread.|