Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > Wheels & Tires - Sponsored By Tire Rack > I done goofed

Wheels & Tires - Sponsored By Tire Rack The place to go for answers on wheel types, tire sizes, offset, wheel patterns and more.
Sponsored By:
Tire Rack


Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: I done goofed Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-12-2012 01:02 PM
DEMENTED SVTF http://www.fswerks.com/brakebleeder.htm
This works very well and it makes it a one man job
11-12-2012 11:46 AM
Neptune15 I'll take a look at the master cylinder sometime down the road. It's a pain that it's not within reach.
11-12-2012 12:54 AM
jetrinka Start at the master cylinder and bleed the lines coming out of it just like the brakes. Have someone step on the pedal while you crack a line, let fluid out, tighten back up.

After this, go to the wheels, do each of them, and then re-test.
11-12-2012 12:04 AM
amc49 No one suggested a new m/c, it was an FYI to those who may come later, also an indicator that m/c bleeding parts may not be available. The inference was that someone might need to cobble up lines to bleed it.
11-11-2012 07:21 PM
Neptune15 I got some help with a mechanic that stopped by real quick.

We managed to get enough air out using the caliper bleeders. The car is now drive-able, but I'd still like a more solid pedal.

Does anyone have any experience with the "phoenix injector" or similar products? I'm willing to part way with some cash if it makes my life easier.
11-11-2012 03:10 PM
sailor I think some responders are only reading part of the thread to answer the "new cyl" question...

The bench bleed suggestion is prob. a guess that it got SO dry that that procedure might help.

I USUALLY vacuum bleed, but sometimes need to pump a bit as well, each method (pressure, vacuum & pump) has "tricks" involved to make it work better and if not done "right" might leave some air in the system.

SHOULD be a simple procedure, but often needs to be done twice or with the right "tricks" to get it done satisfactorily.

Luck!
11-11-2012 12:37 PM
Neptune15 My current m/c isn't faulty, I'm not sure why it's being suggested that I'm installing a new one. There's just air in there.
11-11-2012 04:35 AM
amc49 Just as an FYI, it was getting to the point in the auto store that most M/C makers were not including the bleeding hoses any more as a cost saving measure. Only the most expensive had them and even then not all did. Pretty funny as one of the requirements for lifetime warranty was that you had to bleed the M/C before installing it.
11-10-2012 02:13 AM
08focusse You need to start with bench bleeding the master before you mount, to do this, you install the hoses that come with it into each fitting and route them in to the reservoir and with a full reservoir , pump the master with a large screw driver till there are no more air bubbles .Then you can install it. Once you have it installed, start at the right rear wheel and go around and bleed each wheel .

I have a pdf file that states how to do this from ford not to sure how to u/l it here
11-09-2012 04:01 PM
Neptune15 Yes.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:14 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.