Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > ZETEC Performance (2000-2004) > valve cover torque spec?

ZETEC Performance (2000-2004) The place to chat about any 2.0L Zetec engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: valve cover torque spec? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-07-2012 06:19 PM
amc49 You're freaking out over nothing is what. The bolts are trapped in the rubber grommet molded into cover. Grommets can be part of overall gasket or separate, either way they trap bolts in place so valve cover has gasket/bolts already together to quickly throw it on motor at the factory.
11-07-2012 01:08 PM
StephenElsbree1986 I can't get my bolts out... am I missing something they're all lifted but they're catching on something... I gotta be doing something wrong... I have them all loosen i can just keep turning them I can even pull up a little bit but they feel like they're hooking on something, I do have a SVT not sure if that makes a diffrence.I even poped the garment up with a screen driver and tried prying it off... nothing.. What am I doing wrong
11-06-2012 10:39 PM
Blue5ive ^exactly.
11-06-2012 10:32 PM
amc49 I would not refer to it so much as 'nice and tight'. The bolts are shouldered meaning they go down to hit solid and then anything more you put on you are simply twisting the bolt in two and pulling threads too. I simply go down evenly until I feel them hit and then just enough more to verify they did hit. Using torque wrench there is quite frankly irrelevant since the hit tells you to stop.

6 mm.-1.0 thread pitch like these typically strip aluminum threads at anything over like 9 ft.lbs. I'd stay at 4-6 but if using ft.lbs. wrench you probably have one that is too big for the job, what's needed is a short 6 inch one with a torque that low. The bigger one is simply too big to be accurate with torque that low.

Doesn't matter anyway, I never torque them. Once you figure out all they can do is hit and no further gasket squeezing can occur after that, it becomes easy to simply feel it hit and pretty much stop there. Never broke a bolt or pulled threads, and never have leaks either.

Same thing with the thermostat housings on these, the bolts hit to limit of part, no tightening you can do after that helps a thing, all you are doing is breaking or cracking your stat housing, the damage then shows up later because you preloaded the plastic part too much. The parts were not meant to be that tight, once you hit part solid you have compressed all the gasket that is possible anyway. I love it when guys here talk about going back to retighten more when part leaks, I can practically hear the part crack. Look at how many people have to buy new housings here, I've got 3 zetecs back to '98 and have had housings off all 3 many times and never failed one yet. I don't torque these either, you again look for the part hitting solid, no torque wrench needed.
11-06-2012 08:28 PM
Blue5ive Pretty much. Just get them nice and tight. Nothing crazy. Most of us in Houston crew don't use a torque wrench for this and have never had a problem or leak.
11-06-2012 05:00 PM
StephenElsbree1986 Yes, yes, necro thread but how important is this I don't havea torque wrech can I just tighten em down? and not worry about it.
01-23-2011 11:20 PM
drlucchesi
Thanks

Thanks Focusmaniac. That's what I needed. Appreciate the help.
01-23-2011 09:26 PM
Djzx3 No your about right, it takes 12 inch pounds to equal 1 ft-lb. I used FT-LB's because I got two torque wrenches one that you set and it clicks and one with a little needle that move across a board down near the handle. Either way will work, now you know what it is in either in ft-lb or in inches-lb's.
01-23-2011 09:24 PM
focusmaniaczx3 confirmed
52in/lbs

please make sure you tighten to INCH/lbs and not FT/LBS. but if your ft/lb torque wrench accurately reads and works that low then you can set it to 4.3ft/lbs i think if my math is right. dont trust my math right now though because ive been awake for almost 2 full days working and piddle farting around and im finally crashing for the night.

start on the bolts in the center of the VC and work your way out. no particular order
01-23-2011 09:21 PM
Djzx3 Yea and convert that into FT LB's and it's like 5-6 FT-LB's.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:36 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat