Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Discussions > Ford Focus Builds & General Showroom > my pitch black 02 svt

Ford Focus Builds & General Showroom Post pictures and information of your Focus being built or your car images here. We want to see your Focus! More Images: Visit Our Online Ford Focus Gallery

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: my pitch black 02 svt Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-01-2014 06:44 PM
pitchblack02svt Been a while since ive been on here! No updates, unfortunately..everything was just put on hold for a while. After I got it all pulled apart I found no bearing left on the #3 rod. Lost interest for a little while, while I figured out what I wanted to do with the car. Been thinking about getting back into it and trying to get it going again the past couple days. Just need to save up the funds.
01-06-2014 09:54 PM
sbc17 Any updates?
12-01-2013 08:09 AM
pitchblack02svt Started getting a few parts on order finally, had to take up some of the black Friday deals!
Have the massive pro vct delete kit, massive lower mount bushings, cfm pcv delete, std zetec head gasket, and lower gasket set on the way and off the list. Hopefully I can get more on the way in the next week or two
11-24-2013 10:05 PM
pitchblack02svt
11-24-2013 09:30 PM
pitchblack02svt So today i made a little more progress. Popped off the head and dropped the pan finally.
Got the head off and all looked good there. No scoring or gouges or any thing in the Cylinder wall. A bit of. Carbon build up on the pistons but i think thats normal for an engine with over 180k on it! valves and all looked good, little burnt but good





And when I dropped the pan all didn't go so well...
Looked really sludgey and quite a bit of shavings in the pan.







I the process of welding together a little engine cradle so I can get it up and flipped upside down and pop the windage tray off and check the damage done. Was 20 degrees out and dumping snow so had to cut the day short.
11-14-2013 12:16 PM
pitchblack02svt No problem.

Its going to be a long process until it is finished. But ill definitely be keeping this updated
11-14-2013 12:11 PM
sbc17 Thanks for the advice.

I'll be keeping an eye on your thread to see the progress. :)
11-14-2013 12:03 PM
pitchblack02svt Oh for sure. Once you get it going it seems pretty straight foreward though.
Pretty much goes:
Drain fluids(I totally forgot to and made a big mess of coolant everywhere! Lol)
Start removing engine harness, heater hoses, Rad hoses, etc..
Get the header off and out of the way.
Get the lower dog bone/trans mount out of the way.
pull the intake, fuel rail injectors and stuff. And unbolt the stupid converter support bracket.
Unbolt the AC compressor and PS pump and bungee it out of the way.
Drop the struts(I just pulled them off completely), unbolt the steering linkage and sway bar end link to pull the cv shafts out.
Then pretty much unbolt the upper mounts and pull the engine.

Might of been an easier way to do it, but that's what I did
11-14-2013 11:40 AM
sbc17 I've never done it ever. So that's why I ask. Lol

Yea I figured the hardest part is finding what to remove first.
11-14-2013 11:36 AM
pitchblack02svt You know, the most time consuming part for me was figuring out how to do everything. Never pulled an engine from a fwd car before. But I have about like 15hrs or so into what I've done, give or take.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:32 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Terms of Use : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.