Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus Tech Discussions > General Technical Chat > Zetec valve adjustment....

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Zetec valve adjustment.... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-09-2012 05:57 AM
whynotthinkwhynot
Quote:
Originally Posted by emsvitil View Post

I believe older style tappets had shims, so that's why I thought of that.
Nothing wrong with being frugal, but old pedestal mount rocker arms are not the same as these buckets. The bottom of the pedestal didn't make repeated contact- no moving parts there. Under the bucket, a shim would be continuously beat by the action of the cam against the valve stem/keeper/spring.
10-08-2012 10:30 PM
amc49 That's fine. The intakes hardly wear at all, when I pull them down I simply lap them a bit and throw them back together. The tappets or shims will stay the same. The exhausts however wear quite a bit, as they do they will close up clearances. If I pull head down I recut exhaust valves and seats. I tell the grinding guy not to cut stem tips, then instead of changing tappets or shims (I have one of each) I grind the valve tip to set up the clearance.
10-08-2012 09:44 PM
emsvitil
Yea!!!

YEA!!!


Don't have to do anything.....


Everything measured out ok (a couple were .001 too big, not going to bother)


The .017 was .012 this time.... I know I measured it a couple of times before because it was off compared to the others (multiple turns of crank too.)




10-08-2012 06:11 AM
emsvitil When I measured it a couple of years ago everything was in spec except for one of the exhaust valves (#1 @ .017) Would need .004 thickness to match other exhaust valves.

Haven't taken it apart yet, so I don't know what it looks like under there.

I believe older style tappets had shims, so that's why I thought of that.


I do have the measuring tools (feeler gauges and micrometer) so that's no problem.

Juggling may fix it, or I'll need 1 bucket (unless things have changed alot).


Just being frugal

10-08-2012 05:55 AM
whynotthinkwhynot Do you have anything that you can measure the buckets with?

1) check clearances with feeler gauge
2) make a chart showing clearances for each bucket, and leave room for more numbers under each
3) remove camshafts
4) use micrometer to measure top of buckets for each valve one at a time
5) put that in the valve chart, and reinstall each bucket after measuring
6) replace any buckets that are out of spec
7) reinstall camshafts and check clearances
10-08-2012 04:14 AM
amc49 How loose is loose and intake or exhaust?

You'll only need a bit of thickness. Idea won't work, something that thin will move around to tear up motor. No way to positively locate it to not do so.

You change bucket, they are different thicknesses.

To put shim underneath, the bottom of bucket and top of retainer must be configured to hold shim tightly in place. The shim is hard and must be a certain thickness to overcome the brittleness of the hardness, can't use just a few thousandths thick.
10-08-2012 03:58 AM
sleepyboy Just get a new bucket that's within spec and save your self the trouble. Though I swear I heard of someone doing this before, but I think that might have been for a mustang cobra? Have you tried the search button surly this has popped up before?
10-08-2012 02:52 AM
emsvitil
Zetec valve adjustment....

Awhile back I had checked the valves on my parents 2002 SE zetec sedan.

1 valve is out of spec (loose).


I left it be at the time, but I am currently changing the timing belt so figured I may fix that....


I have an idea that might work.


As anyone just put a shim under the bucket to tighten the valve adjustment?


Don't see why it wouldn't work.


Comments?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:05 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat