Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > SPI Performance (2000-2004) > SPI not wanting to stay running

SPI Performance (2000-2004) The place to chat about any 2.0L Split Port Injection engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: SPI not wanting to stay running Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-20-2012 12:46 PM
ponddogs got the noid light set and went out and tested the fuel system, no light when cranking the engine, I even tested the kit on a running focus to see if it was working, also replaced the wire harness from the firewall to the engine, no light, is there a way to test the ECU without taking it to the ford house?
07-31-2012 04:37 PM
Chustle209 depending on your mechanical inclination, parts access and the like, doing a zetec swap could be an option. While that would get you off of valve drop watch, I don't know what reaction that would have with the all of the other problems mentioned. obviously any directly related to your engine would be gone/change since not same engine.

I understand your situation. My 03 SPI has been sitting in my driveway for the past 3+ mo as I figure out what to do with it.
07-30-2012 01:31 PM
ponddogs That has cross my mind every day I look at it, I have even thought of just parting it out, too many new parts on it just to sent it to the junk yard, mileage 117 k, all stock
07-29-2012 04:37 PM
Chustle209 I see this is your 2nd post so 1) 2)While I don't know what to tell you regarding your currently listed problems, I know one from 1st hand experience and that countless people on here can also attest to. The SPI engine, at least factory, is damn near a ticking time bomb. The SPI is the Ford CVH engine which has the lovely problem of the valve seats dropping out and messing up the engine. You don't say how many miles are on the car or if it is the stock engine but assuming they are, depending on how mechanically inclined you are & how much $$ you are looking to put into the car (in central CA, talking to the tune of around $2000). It might be beneficial to get rid of it.

Just food for thought.

http://en.wikipedia.org/wiki/Ford_CV...ommon_Problems
http://www.focusfanatics.com/forum/showthread.php?t=275905
07-28-2012 03:57 PM
ponddogs
SPI not wanting to stay running

2003 SPI engine, bought the car with a pining noise when accelerate and wanting to die after the engine warm up, ford house said bad gas, drained fuel tank 3 times, change out filter 3 times and the in-tank fuel pump, change out plugs, wires, coil pack, crank sensor and cam sensor, had the engine cat tested for back pressure, had the fuel injectors checked, getting 35 psi at injector rail, then engine drop number 1 cylinder valve exhaust seat, change out head assy, piston and piston rod, timing belt and engine gasket set, engine would not start, back to ford house, they said engine oil pump is not working, change out pump, oil light now goes out when cranking but when cranking engine it's sound like if the engine timing is too far advance, had the ECM reflashed, rechecked the engine timing belt both dots and key way locations, checked the engine compression 160 160 155 160, change out the throttle body off a running focus, now if you pour some fuel in the throttle body it will start but only stay running if you feather the throttle and the pining noise is back with a miss, no engine codes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:30 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat