Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > ABS Light

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: ABS Light Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-29-2013 11:31 PM
carlos1984 I am having abs light after garage replace bearing ,cylinder, sensor and abs ring on my right rear, would it be possible to let me know where the abs control module is located, is the wheel speed sensor the same as abs sensor if so where is it located and do i need to remove the wheel?

Sorry for all the questions, im am just hoping to fix this issue myself,as I feel I keep being screwed over by garages.Plus i dont have the money to get this problem repaired.
07-09-2012 06:08 AM
rbrad6937 Problem fixed. The steps below outline what I had to do for the repair.

1. Removed battery and battery holder from car.

2. Unplugged connector from ABS control Module.

3. Unplugged connector from right front Wheel Speed Sensor.

3. Performed a continuity check between pins 5 + 6 on the ABS control module connector and the pins on the disconnected right front wheel speed sensor.

The continuity from ABS module Pin 6 to the wheel speed sensor connector was good but I found an open condition at pin 5. I did an inspection of the pins and connector at the wheel and it all looked like new. I started to pull the wire harness out of the plastic outer protective jacket at the right wheel going towards the ABS control module. About 12 inches in I found a broken wire. I soldered the wire back together, applied sleeving, plugged it all back in and took the car for a test drive. After going about 100 feet the ABS light finally went out. I am totally stumped as to why the wire broke where it did. It was in an area where there should be no flexing. It may have been a problem that started from the previous owner. It took me about 2 hours to finally find the problem, fix it, and get it back together. Hope this helps someone else with similar problems.
07-05-2012 07:16 AM
239rsw What happened to the live free die free? Kidding aside, don't they sell cars without ABS nowadays in NH?
07-04-2012 08:27 AM
rbrad6937 I live in New Hampshire and the ABS light is on and I cannot clear the C1145 code after replacing the right front wheel speed sensor. In New Hampshire this is considered a safety issue which will cause a failed inspection.
07-04-2012 08:16 AM
239rsw Inspection Sticker. If it is emission, nothing to worry about. ABS is not emission related. I passed emission twice with the ABS on. I haven't fixed mine yet - both front and left rear wheels. It came out when the when the wheel bearings were replaced incorrectly.
07-04-2012 07:35 AM
rbrad6937 I keep reading that this is a common problem with the Focus but I get no replies on what the possible fixes are. Could this be the ABS control module that is causing the one error to the right front wheel sensor? Does anyone know how to trace the wires from the wheel speed sensor back to the control module? Schematics? I only have until the end of the month to get an inspection sticker and I don't want to take it to the dealer if I don't have to.

Thanks in advance

Robert
07-03-2012 06:06 AM
rbrad6937
ABS Light

2006 ZX4, SES, 5spd,
My abs light has been on constantly. I recently checked it with a abs capable code reader and a C1145 code came up. This code is for a failure to the right front wheel speed sensor. I replaced the sensor last night and drove to work this morning (35 miles) but the light will not go out. Do I have to clear the code with the reader or will it go out on its own? Is there something I am missing?

UPDATE: I just tried to clear the code with the reader but the light and code are still there.

Robert

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:47 PM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Acura TLX or Fiesta ST. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.