Ford Focus Forum, Ford Focus ST Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum > Ford Focus Tech Discussions > General Technical Chat > ATX trans gasket

General Technical Chat This section is for technical discussions relating to general maintenance, electrical issues, engine trouble, and recalls.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: ATX trans gasket Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-01-2012 11:01 AM
amc49 I'd use a minimum of 30 pounds weight. The RTV will dry lumpy otherwise and lumpy leaks very easy.

I've put on hundreds of gaskets dry and no leak for years. Clean and DRY surface is the key, 99% of time when I view others' errored work the surface is still dirty or oily. Oil and uncured RTV absolutely do not mix. ANY RTV and ATX do not mix, the little BBs come loose and if get in valve body problem city.

The gasket can easily be overtightened to leak too. The pan must be prepped by knocking pull in back out at all the bolt holes. The pulled in area at holes relieves the rest of flat between holes to leak.

I'll take a gasket and no RTV any day, although I have no trouble either way making it work.
01-29-2012 11:19 PM
emsvitil Glue the gasket to the pan with RTV.

Put some plastic wrap down on floor.

Put gasket and pan on plastic wrap.

Add some weight to pan (stacks of old newspaper work)

Let sit overnight.


Install pan with RTV smeared on gasket to tranny.

No leaks.


If you don't let the gasket and RTV dry onto the pan, when you tighten the bolts the gasket tends to be pushed out from between the pan and tranny........(RTV makes a great lubricant if it isn't dry).
01-29-2012 10:42 PM
JET DH I know the tourqe is pretty low, like 10 whatever pounds.

15nm - google
01-29-2012 10:09 PM
md2009 I've seen a product that you spray on the gasket which is supposed to help with sealing. It comes out red, and is a very tacky substance.

The #1 mistake folks make when installing a pan gasket is OVER tightening the bolts. If you go too tight, you will split the gasket and it will leak like civ. The correct torque is probably measured in inch pounds, although I don't have the specs in front of me. If you take the pan off, I would choose to either use the gasket or use gasket maker, but not both. Personally, the gasket has always worked fine for me.. just make sure you get the right torque specs!
01-29-2012 09:58 PM
JET DH
ATX trans gasket

So I changed my transfilter with the Fram kit a while back and since I've had a leak coming from somewhere. I can't find the leak itself, but I'm going to try the simple stuff first.

My question is what is the best way to make sure it is sealed completely?

I'm kind of thinking that if I just use the gasket, it may get a tear or something and I'll be back where I started. If I use some RTV as backup, I am thinking about putting it on the pan then putting the gasket on the RTV, and installing the pan creating a sandwich kind of seal. Or I could put the RTV on both sides of the gasket, but I think that may be overkill.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:44 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Cadillac ATS-V, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area.