|03-29-2017 10:13 AM|
I am still working with the Standard harness that I altered. The only European part is the harness that connects the rear tails and rear fogs. I can't figure out why my indicators and brake lights aren't working but I have an idea that it has something to do with the third brake light and one rear fog light coming on when the key is turned.
All the front lights seem to be working except for the turn signals.
I am going to work on it tonight and see if I can track down the issue.
|03-28-2017 03:38 PM|
|ORANGECRUSH||Tyler..if you haven't gotten to the head light connector I can lead you there. I've been all through the manual locating terminals and tracing down the fuse panel/relays/pcm to use the RS pcm I've got. I've already gotten in it and synced my keys to it. That fan issue we were discussing doesn't exist anymore. I'm using the RS engine bay harness, 14K733 along with pcm harness, 12A522. Also crossed over the instrument cluster pin outs to see if I'll get the correct signals to it, and re-pin if needed. The biggest issue left is to reorganize the bulkhead connector cause the RS uses one and the SVT uses two. But the headlamp switch was studied to determine if I wanted to connect up the headlamp motors. I found within IDS where to do adjustments on the headlamp motors to preset them.|
|03-28-2017 11:23 AM|
Its going in for final paint correction this week and I hope to have it running within the month. There was a major screw up with a billet MAF I purchased and an entire pipe had to be redone.
Other than that there are a few wiring gremlins yet but I don't think it is anything major.
If I find some time this week I will post an update.
|03-12-2017 08:20 PM|
Anything going on with this sweet build?
Sent from my LG-H901 using FF Mobile
|04-07-2016 06:43 AM|
-I installed a dimming rear mirror which has three wires (ground, Ignition live, and the mystery wire) I need to find where the mystery wire goes but I believe I am just missing the power wire.QUOTE]
Does your dimming mirror have a switch or button on it to turn on/off? If so that third wire is probably for outer mirrors with dimming. Usually (key word) all the strategy is in the interior rear view because that's where the light sensor is, when that gets dim then the outside gets dim. If you want to test just connect your hot and ground leads to appropriate voltage and see if it powers up. Then use a flash light or something similar (no LED, has to be halogen) shine the light onto the sensor in the mirror and see if it gets dark. It should, if it works the way I'm thinking
|04-06-2016 11:01 AM|
Update on electrical:
I have made some progress I don't want to turn over the car yet until some of these are issues are sorted. Here is a quick breakdown of how my car is wired/setup and then I will list the current issues I am facing to see if we can come to some solutions.
Mach HID Headlights
-Turn signal bulb has been converted to a white running light that will always be on once the key is turned
-Small light has been converted to a running light that will come on when the switch is turned to running lights
Headlight Switch is a European Switch
-This version includes all the workings for the rear fogs, headlight levelers, parking lights.
-currently not wired up for parking or rear fogs
Rear Tail light and Fog harness
-This is the true euro harness and has not been spliced yet (I wanted to see what worked first hoping for the best)
Front Bumper and Fender Turn Signals
-Both wired up to previous turn signal leads
What Currently happens at all headlight switch stages:
Turn on Key
-Both front running lights come on.
-Third brake light comes on along with bottom left fog/reverse light
Turn light switch to running lights
-Only right side of car lights come on (passenger side mini bulb indicator and brake light bulb)
Pull for Front fog lights
-Both fogs come on
Turn on Headlights
-Both headlights fire up
Obvious problems so far:
-Driver side running lights do not come on
-With ignition on Third Brake light and drivers side reverse fog comes on (need to still check bulb on passenger side rear Fog)
-Brake light don't seem to be working with the compression of the pedal
-Horn does not work (we can hear a clicking solenoid noise when pressed but nothing else)
-turn signals do not work currently (I believe they should with the ignition on, I need to check the hazard switch yet)
-Whatever Gauge Illumination wire I used is not working as I am not getting any power to my mechanical oil pressure gauge I will find another soon with the multi-meter
-I really need to find a pin readout for the euro headlight switch (I have the ford work shop manuals so I will check there first and then I will contact my friends in Europe. I am not too concerned about the parking setup but I want the rear fogs to work correctly.)
-I installed a dimming rear mirror which has three wires (ground, Ignition live, and the mystery wire) I need to find where the mystery wire goes but I believe I am just missing the power wire.
I know this is a lot right now and I am going to continue working at it but I thought I would post it up for people to share there thoughts if they have answers. I also did a quick search on the topic yesterday and I have a few pages to read yet. I think I am going to post some pictures up as well of a few things that are going on so it is easier for everyone to visualize.
|04-06-2016 11:00 AM|
|04-04-2016 12:57 AM|
|ZXthrizzle05||patience has been a virtue with this project|
|03-31-2016 10:44 AM|
|gregor_42||Yes! Been waiting a long time to hear this kitten roar!|
|03-31-2016 10:18 AM|
Hooked up the battery last night to make sure we are getting power to certain areas and ran into an issue with getting power to the actual key. I can get power to the light switch which turns the dash lights on but I am not getting much else although the correct voltage is definitely circulating.
I took some pictures and was going to post up my diagram but after looking over it some more in the morning I think I have it figured out.
I need to try one more thing tonight and if I am still having issues I will be back here to hopefully find some answers.
If I can get the engine oil primed this weekend I will order the start up tune so we can all finally hear this thing run!
|This thread has more than 10 replies. Click here to review the whole thread.|