|06-18-2012 03:48 PM|
I sold my ST170 recently, but before i did i had to repair the IMRC as i had the p1518 error. I just want to tell people that i replaced my ST170 IMRC with one from a Cougar. The part number matched and the part looked (inside and out) identical in every way.
Fitted and worked no problem. Saved myself approx £150 as for some reason for the Cougar they are much much cheaper.
|05-04-2012 09:21 PM|
|bespurcell||I love this write up. I took mine apart today because I'm getting the famous IMRC stuck open code. I would like to add for those of you that are uncomfortable with desoldering the connector that with a little patience (approximately 5-10 mins.) and a pocket knife you can scrape off the epoxy around the connector and remove it all together.|
|01-08-2012 06:46 PM|
|blackjack||Is there anyway to remove the PCB without having to un-soldiering it from the wiring harness plug?|
|12-26-2010 05:23 PM|
|PiSTOLpete717||cool thanks for posting this...|
|12-23-2010 02:32 AM|
|94Cobra||Hey, besthaticouldo, awesome avatar! How many tries did it take to get the cat to wear that orange peel and let you shoot it?|
|11-05-2009 05:36 AM|
You say you recently replaced your DSI clip? Did it break? If so, that could have allowed the gear to destroy itself. Seems that they are pretty reliable most of the time....don't hear much about stripped gears.
Oh....seeing as the motor is very similar (if not the exactly the same) as those used in RC model cars/trucks, you might get lucky and find a gear from one of them that is the same and will repair the box for a dollar or two. Only problem will be measuring the gear and finding the replacement. Good luck!
|11-04-2009 12:55 PM|
After a few more minutes of thought ('I'm not the sharpest spoon in the shed' and it takes me awhile to work through a problem), I'm almost positive that the problem is that the plastic wheel is stripped-out. When the plastic wheel is rotated by the metal gear so that the plastic wheel pulls on the cable, the plastic wheel slips and releases the cable. The plastic wheel is stripped out just enough so that the it be partially rotated, but when a certain amount of torque is placed on it and it is rotated too far, it slips and releases the cable. I'm going to try and put a metal screw into the plastic wheel so that the metal gear has something of substance to push against. If it works out, I'll post my results. If anybody has any other suggestions, let's hear 'em.
And again, why couldn't they just use metal instead of plastic? Who knows how many people have spent $100-$200 bucks or more on replacing this whole unit just because a $0.10 plastic wheel strips-out?
|11-04-2009 12:42 PM|
this thread is just too informatve my heads gonna explode...A+ for you!
|11-04-2009 12:17 PM|
Old thread, I know, but I'd like to revive it because I'm having problems with my IMRC and if it's just a quick fix (like cleaning it) than I'd prefer to keep the original instead of buying a new one.
So, the problem I'm having is that the IMRC keeps cycling. It keeps switching back and forth between the two different runners. It's loud and you can hear the IMRC cycling between being open and closed. I've recently replaced my DSI clip, so that shouldn't be a problem. The cable from the IMRC is still attached to the post on the DSI clip as it should be.
I've taken the IMRC out of the car and I have it taken apart like GuySA shows above. The only problem I can see is that the little plastic wheel that pulls on the cable is kinda stripped out (there's some white plastic shavings in the bottom of the box). So it's possible that this plastic wheel is slipping, but I'm not sure if this is the problem. If this was the problem then I don't think the cable would be able to be pulled or released at all, would it?
Lastly, why in the eff didn't they just spend a few extra pennies and use a metal wheel instead of the cheap plastic one? Thanks guys and gals for any help/advice you can give me.
|03-27-2009 03:50 AM|
nice work, OP. I'll admit that I couldn't keep from pulling that guy apart when i removed it from my car. I did not flip the board though, so this thread was still interesting :)
btw if anyone breaks their IMRC controller, I've got a spare just chillin' in my closet.
|This thread has more than 10 replies. Click here to review the whole thread.|