|11-11-2007 11:22 AM|
|Bar||I've had trouble getting the fluid level right, myself. According to the specs from this site, it takes 3.2 qts. to fill it back up from a pan drop. Next time, I think I'll just add 3 qts. 7 oz. and be done with it.|
|11-09-2007 07:53 PM|
|09-14-2007 02:59 PM|
|lduran||I forgot about this thread. I did get it drained out. Thanks to all who helped.|
|07-08-2007 09:49 AM|
Did you get the fluid drained yet ? Be sure to post back up to let us know how it went once done.
|07-08-2007 08:40 AM|
|hotfocus||Too much fluid can cause your seals to burst...drain it to the right level before driving.|
|07-05-2007 10:01 AM|
|07-05-2007 01:13 AM|
Don't look in the bucket while the car is on- it might be a better idea to disconnect the coil or the inertia switch and just crank it.
Best of luck!
|07-04-2007 11:35 PM|
|lduran||Thank you so much for all who replied. I think I am going to try your method FordZX32000, it sounds like the easiest way to do it with the tools I have on hand.|
|07-04-2007 11:02 PM|
Hay FORDZX32000 With a gasket in place the next pan drop should be a much easier If a leak does develop then we can re torque, up to 10 ft.lb. if necessary, right? I did consider a DIY tranny flush as suggested by others on this forum: Pull the upper cooler hose, run the car in neutral until 3 qts is pumped out, refill and repeat. This is supposed to be safe, especially as a way to flush the torque converter after a pan drop. May do this at the 90K pan drop.
So from there here's what I did.
1. I pulled the car up onto the car ramps.
2. Took a look at the pan bolts and then looked at the tranny cooler lines.
3. I went for the tranny cooler lines as they appeared to be the easy route.
4. There are two tranny cooler lines that run into the tranny cooler located in the front of the car behind the radiator fans. (A) Top cooler line is the supply line. (B) Lower cooler line is the return line.
5. On my car the top cooler line had a rubber hose that connects to a metal line that runs into the cooler. The rubber line was connected with a hose clamp.
6. I unscrewed the hose clamp and slid the rubber hose off.
7. I had a bucket there to catch any fluid.
8. I put the car in neutral with the parking brake on.
9. Had a friend start the car while I'm directing the gushing fluid into the bucket. FYI, Once the car is started it will pump that fluid out real quick!!!
10. I let it pump out about 3-4 qts of fluid and then shut the car off.
11. I reconnected the hose and added 2-qts of new fluid.
12. Back the car off the ramps and let it get to operating temp as well as shifting thru all of the gears.
13. I then added fluid as needed until I had the corrrect level.
I can tell you it was not a bad job to do in order to remove the overfill of fluid.
However I would advise being careful as not to mess up your tranny by pumping all the fluid out of the T/C which is what I did not do. I don't know if it could screw something up or not with the car running with all of the fluid out of the T/C.
Anyway I hope this will help you and others.
Here's the full thread.
|07-04-2007 08:57 PM|
Oil Extractor: http://www.griotsgarage.com/catalog.jsp?&SKU=10122
Suction Gun: http://www.amazon.com/Plews-Suction-Gun/dp/B0008D6O7C
Vacuum Brake Bleeder: http://www.amazon.com/MityVac-MV6815...3597020&sr=1-6
|This thread has more than 10 replies. Click here to review the whole thread.|