Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum - Reply to Topic
Ford Focus Forum
HomeContact UsAbout UsGalleryDiscussion ForumsMarketplace


Go Back   Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum > Ford Focus First Generation > ZETEC Performance (2000-2004) > Timing belt troubles on my ZX2

ZETEC Performance (2000-2004) The place to chat about any 2.0L Zetec engine performance, tuning and exhaust related upgrades.

Search This Forum | Image Search | Advanced Search    
Ford Focus Tire & Wheels FocusFanatics Merchandise

Thread: Timing belt troubles on my ZX2 Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Ford Focus Forum, Ford Focus ST Forum, Ford Focus RS Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-30-2005 02:37 PM
crazymechanic call steeda or some other company that sells cams for the focus. they might have the TDC crank peg, and if not, they probably know where you can get one.
06-30-2005 01:45 PM
xxltall Well I tried once and it was not right so now I want to do every step. I do not want to do this a third time so if I can find it I will use it.
06-30-2005 10:27 AM
j0hnZ True you don't have to have it but would you rather do it right the first time?
06-29-2005 09:40 PM
elitekorri You don't need the crank TDC... just turn over your crank with a screwdriver in your cyl1/4 until you see the screwdriver hit TDC (top dead center). Don't move your engine... lock your cam in place horizontal.... put on your cam belt.... tighten your cam belt... tighten your cam sprockets... done! (now just dyno tune your cam retard/advance to get best #'s)
06-29-2005 04:16 PM
xxltall I had the one at the end of the cams. I just used a piece of flat stock I cut to the right size. The crank TDC peg how can I get one of these?
06-28-2005 05:43 PM
crazymechanic there's actually two timing tools, though if you're real careful you only need one. one is the cam alignment bar, the other is a crank TDC peg. you remove a blanking plug from the block and put the peg in and turn the crank over until it hits the peg. now you're at cyl 1 TDC
06-28-2005 05:38 PM
j0hnZ
Quote:
Originally posted by crazymechanic
when the cams are properly lined up and the crank is at TDC cyl 1 compression, the intake cam should have the cylinder 1 lobes pointing toward the back of the car, and the exhaust cam should have the lobes pointing toward the front.
Correct face the cam lobes facing apart. You should have gotten a cam alignment tool. There are indents on the cams opposite of the cam gears you stick the alignment tool there and stick the belt on. Of course after cylinder 1 is at TDC.

By the way their are a million zx2 sites all over the place. Check my sig for one of them.
06-28-2005 08:51 AM
crazymechanic when the cams are properly lined up and the crank is at TDC cyl 1 compression, the intake cam should have the cylinder 1 lobes pointing toward the back of the car, and the exhaust cam should have the lobes pointing toward the front.
06-28-2005 08:27 AM
xxltall Some more info and questions that can shed some light.
Yes this is on the ZX2 Escort not a ZX3 Focus. You guys seem to know more about the motor than most the other Ford small car guys and this is why I ask for your help. I have been trying every Form forum tiring to find the proper way.

Tension is correct. That is very easy to do I know that is good.
I thought I had all the timing marks set but the instructions had some different looking marks. I would like to find a way to verify the marks if possible.
I did turn the motor over by hand to see that I would not crunch a valve and it does run and does not show any sign of crunching, thank God.
Some people in the other forums have said to stick a screwdriver in cyl #1 and find TDC that way rather than using the marks.
When the motor is in TDC what should the cams look like? How can I tell if they are in the right spot?
How can I reset the VCT?
I sooo wish I had the money just to take it to someone to get it right but it really was not that hard of a job except for this problem.
Thanks,
Rob
06-28-2005 01:01 AM
crazymechanic actually, if the timing procedure isn't followed correctly, the VCT will not work properly. the VCT depends on the pulley being in a certain position when it is tightened to the 0 degree times camshaft.
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:24 AM.


Copyright 2002-2014 FocusFanatics.com. All Rights Reserved : Privacy Policy : Advertise Information

Focus Fanatics Ford Focus Forum offers many fun ways for you to engage with other Ford Focus Owners from across the world. Whether it be about the aftermarket performance modifications, technical how-to's, European tuned suspension or awesome fuel economy similar to the Audi S3, Ford Fusion and Acura TLX. You can find all Ford Focus and Focus ST related information here. Join our Ford Focus discussion forums and chat with local Focus enthusiasts in your area. Challenger Hellcat - Charger Hellcat